2904595 Phoenix Contact AC/DC Power Supplies

2904595 Product Details

• Height
  106 mm
• Depth
  90 mm
• Degree of protection
  IP20
• Installation distance right/left (active)
  15 mm / 15 mm (POut ≥50% )
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Installation height
  ≤ 5000 m (> 2000 m, observe derating)
• Input fuse
  3.15 A (slow-blow, internal)
• Nominal output current (IN)
  5 A
• Connection in parallel
  Yes, for redundancy and increased capacity
• Typical response time
  350 ms
• Protection class
  II
• Conductor cross section solid max.
  2.5 mm²
• Conductor cross section AWG max.
  14
• Standard – Safety extra-low voltage
  IEC 61010-1 (SELV)
• Standard – Limitation of mains harmonic currents
  EN 61000-3-2
• Flicker
  EN 61000-3-3
• Frequency range
  50 Hz ... 60 Hz
• Output
  1 kV (Test Level 3 - symmetrical)
• Conducted interference
  EN 61000-4-6
• Asymmetrical conducted disturbance variables
  EN 61000-4-16
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 11.0
27040701
Width
22.5 mm
Installation distance right/left (active, passive)
0 mm / 0 mm (POut ≤50 %)
Installation distance top/bottom (active)
30 mm / 30 mm (POut ≥50% )
Ambient temperature (start-up type tested)
-40 °C
Dielectric strength maximum
300 V AC (60 s)
Nominal power consumption
32.8 VA
Type of protection
Transient surge protection
Static Boost (IStat.Boost)
6.25 A (≤ 40 °C)
Protection against overvoltage at the output (OVP)
< 8 V DC
Residual ripple
< 40 mVPP (with nominal values)
Efficiency
typ. 87.4 % (120 V AC)
Conductor cross section AWG min.
24
Standard - Safety of transformers
EN 61558-2-16
UL approvals
UL Listed UL 61010-1
Conducted noise emission
EN 55016
Contact discharge
8 kV (Test Level 4)
Signal
0.5 kV (Test Level 2 - symmetrical)
Voltage
1 kV (symmetrical)
Voltage dips
EN 61000-4-11
Voltage dip
0 %
Attenuated oscillating wave
EN 61000-4-18
Criterion C
Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.
Installation distance right/left (passive)
5 mm / 5 mm (POut ≥50% )
Installation distance top/bottom (passive)
30 mm / 30 mm (POut ≥50% )
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Frequency range (fN)
50 Hz ... 60 Hz -10 % ... +10 %
Inrush current
typ. 9.1 A (at 25 °C)
Mains buffering time
typ. 52 ms (120 V AC)
Setting range of the output voltage (USet)
5 V DC ... 6.2 V DC (constant capacity)
Dynamic Boost (IDyn.Boost)
8 A (≤ 60 °C (5 s))
Control deviation
< 0.3 % (change in load, static 10 % ... 90 %)
Maximum power dissipation in no-load condition
< 0.37 W (120 V AC)
MTBF (IEC 61709, SN 29500)
> 1890000 h (25 °C)
Conductor cross section flexible max.
2.5 mm²
Standard - Safety of power supply units up to 1100 V (insulation distances)
DIN EN 61558-2-16
Standard - Electrical safety
IEC 61010-1 (SELV)
Standard - power supply devices for low voltage with DC output
EN 61204-3
Harmonic currents
EN 61000-3-2
Electromagnetic HF field
EN 61000-4-3
Comments
Criterion A
I/O/S
asymmetrical
Frequency
60 Hz
Attenuated sinusoidal oscillations (ring wave)
EN 61000-4-12
Criterion A
Normal operating behavior within the specified limits.
ECLASS 5.1
27242213
Installation distance top/bottom (active, passive)
30 mm / 30 mm (POut ≤50 %)
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Climatic class
3K3 (in acc. with EN 60721)
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Current consumption
0.37 A (100 V AC)
Recommended breaker for input protection
6 A ... 16 A (Characteristic B, C or comparable)
Nominal output voltage
5 V DC
Feedback voltage resistance
≤ 16 V DC (16 V e-caps in output circuit)
Power loss nominal load max.
< 3.7 W (120 V AC)
Insulation voltage input/output
4 kV AC (type test)
Connection method
Push-in connection
Conductor cross section solid min.
0.2 mm²
Standard - Safe isolation
IEC 61558-2-16
SIQ
CB-Scheme (IEC 61010-1, IEC 61010-2-201)
Noise emission
EN 55016
Discharge in air
15 kV (Test Level 4)
Fast transients (burst)
EN 61000-4-4
Surge voltage load (surge)
EN 61000-4-5
Power frequency magnetic field
EN 61000-4-8
Pulse-shape magnetic field
EN 61000-4-9
Test level 1
16.67 Hz 50 Hz 60 Hz 150 Hz 180 Hz (Test Level 3)
ECLASS 10.0.1
27040701
Degree of pollution
2
Discharge current to PE
< 0.25 mA (264 V AC, 60 Hz)
Protective circuit/component
Varistor
Connection in series
yes
Output power
25 W
Net weight
0.184 kg
Conductor cross section flexible min.
0.2 mm²
Stripping length
10 mm
Standard - safety for equipment for measurement, control, and laboratory use
IEC 61010-1
Rail applications
EN 50121-3-2
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Electrostatic discharge
EN 61000-4-2
Test field strength
1000 A/m
Input
2 kV (symmetrical)
Additional text
Test Level 2
Number of periods
0.5 / 1 / 5 / 50 periods
Test level 2
16.67 Hz 50 Hz 60 Hz (Test Level 2)
ECLASS 9.0
27040701

Product condition