8BVI0330HCSA.000-1 B&R Electronic Components

Product Details

• Weight4.3 kg
• Dimensions Depth Cold plate
  212 mm
• Temperature Operation Maximum
  55°C
• Dimensions Depth Pass-through mounting
  209 mm
• Temperature Operation Nominal
  5 to 40°C
• Sine/Cosine inputs Differential voltage At standstill
  0.8 to 1.35 V
• Sine/Cosine inputs Differential voltage In motion
  0.5 to 1.35 V
• Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves
  0.5 to 16 mm²
• Encoder power supply Protective measures Overload-proof
  Yes
• Terminal connection cross section Approbation data CSA
  20 to 6
• Terminal connection cross section Approbation data UL/C-UL-US
  20 to 6
• Reduction of continuous current depending on switching frequency and mounting type Switching frequency 20 kHz Pass-through mounting
  0.24 A/K (starting at -137°C)
• Reduction of continuous current depending on switching frequency and mounting type Switching frequency 10 kHz Cold plate mounting
  0.62 A/K (starting at 6°C)
• Reduction of continuous current depending on switching frequency and mounting type Switching frequency 10 kHz Pass-through mounting
  0.37 A/K (starting at -36°C)
• Reduction of continuous current depending on switching frequency and mounting type Switching frequency 5 kHz Cold plate mounting
  0.8 A/K (starting at 45°C)
• Dimensions Height
  317 mm
• Dimensions Width
  106.5 mm
• Relative humidity Transport
  Max. 95% at 40°C
• Relative humidity Operation
  5 to 85%
• Temperature Storage
  -25 to 55°C
Permissible mounting orientations Hanging vertically
Yes
Relative humidity Storage
5 to 95%
Installation elevation above sea level Maximum
4000 m
Permissible mounting orientations Horizontal, face up
Yes
Temperature Transport
-25 to 70°C
Input voltage Maximum
30 VDC
Switching threshold Low
<5 V
Position Noise
---
Electrical isolation Input - Inverter module
Yes
Position Resolution @ 1 VSS
Number of encoder lines * 5700
Position Accuracy
---
Reference input Differential voltage for low
≤-0.2 V
Reference input Signal transmission
Differential signal, symmetrical
Sine/Cosine inputs Signal frequency (-3 dB)
DC up to 200 kHz
Sine/Cosine inputs Max. input frequency
200 kHz
Synchronous serial interface Signal transmission
RS485
Sine/Cosine inputs Terminating resistor
120 Ω
Protective measures Undervoltage monitoring
Yes
Encoder power supply Output voltage
5 V ±5%
Electrical isolation Encoder - ACOPOSmulti
No
Encoder power supply Sense lines
2, compensation of max. 2 x 0.7 V
Sine/Cosine inputs Differential voltage deviation per signal period
±10%
Max. motor line length depending on switching frequency Switching frequency 20 kHz
25 m
Output voltage DC bus voltage (UDC): 260 to 315 VDC
25 VDC * (UDC/315)
Protective measures Short-circuit and ground fault protection
Yes
Output voltage DC bus voltage (UDC): 315 to 800 VDC
24 VDC ±6%
Certifications EAC
Yes
Protective measures Overload protection
Yes
Power dissipation depending on switching frequency Switching frequency 5 kHz
[0.07 * IM² + 7.3 * IM + 40] W
Encoder monitoring
Yes
Extinction potential
Approx. 30 V
Encoder power supply Protective measures Short-circuit proof
Yes
Reduction of continuous current depending on switching frequency and mounting type Switching frequency 20 kHz Cold plate mounting
0.32 A/K (starting at -82°C)
Reduction of continuous current depending on switching frequency and mounting type Switching frequency 5 kHz Pass-through mounting
1.26 A/K (starting at 40°C)
Permissible mounting orientations Standing horizontally
No
Installation elevation above sea level Nominal
0 to 500 m
Switching threshold High
>15 V
Switching delay Rising edge
52 µs ±0.5 µs (digitally filtered)
Switching delay Falling edge
53 µs ±0.5 µs (digitally filtered)
Input voltage Nominal
24 VDC
Electrical isolation Input - Input
Yes
Reference input Differential voltage for high
≥0.2 V
Reference input Common-mode voltage
Max. -5 V to +9 V
Reference input Terminating resistor
120 Ω
Sine/Cosine inputs Signal frequency (-5 dB)
<300 kHz
Sine/Cosine inputs ADC resolution
12-bit
DC bus capacitance
990 µF
Sine/Cosine inputs Common-mode voltage
Max. ±7 V
Variant
ACOPOSmulti backplane
Input capacitance
32.9 µF
Sine/Cosine inputs Signal transmission
Differential signals, symmetrical
Synchronous serial interface Data transfer rate
781.25 kbit/s
Encoder power supply Load capacity
300 mA
Input voltage
25 VDC ±1.6%
Protective measures Open-circuit monitoring
Yes
Variant U, V, W, PE
Connector
Protective measures Overload and short-circuit protection
Yes
Max. power consumption
25 W + PSMC1 + PSLOT2 + P24 V Out + PHoldingBrake
Variant Shield connection
Yes
Max. motor line length depending on switching frequency Switching frequency 10 kHz
25 m
Max. motor line length depending on switching frequency Switching frequency 5 kHz
25 m
Power dissipation depending on switching frequency Switching frequency 20 kHz
[1.85 * IM² + 3.8 * IM + 300] W
Reduction of continuous current depending on installation elevation Starting at 500 m above sea level
3.3 Aeff per 1000 m
Power dissipation depending on switching frequency Switching frequency 10 kHz
[0.2 * IM² + 11.1 * IM + 130] W
Voltage Nominal
750 VDC
Certifications CE
Yes
Degree of protection per EN 60529
IP20
Certifications Functional safety
Yes (openSAFETY)
Module width
2
Pollution degree per EN 61800-5-1
2 (non-conductive pollution)
Certifications UL
cULus E225616; Power conversion equipment
Discharge capacitance
0.22 µF
Overvoltage category per EN 61800-5-1
III
Modulation compared to ground potential
Max. ±38 V
Max. power consumption per encoder interface
PSMC[W] = 25 V * (0.376 A + 0.35 * IEncoder[A])
Circuit
Sink
Input current at nominal voltage
Approx. 10 mA
Status indicators
UP/DN LEDs
Max. encoder cable length
50 m
Response threshold for undervoltage monitoring
24 VDC -2% / -4%
Max. switching frequency
0.5 Hz
Type
SinCos
Connections
15-pin female DSUB connector
Response threshold for open-circuit monitoring
Approx. 0.5 A
Max. internal resistance
0.15 Ω
Terminal cable cross section dimension of shield connection
23 to 35 mm
Output voltage
24 VDC +5.8% / -0.5%
Continuous current
4.2 A
Insulation stress of the connected motor per IEC TS 60034-25:2004
Limit value curve A
Max. extinction energy per switching operation
3 Ws
Possible switching frequencies
5 / 10 / 20 kHz
Peak current
83 Aeff
Max. output frequency
598 Hz
Quantity
2
Nominal switching frequency
5 kHz
B&R ID code
0xE0B6
Continuous power per motor connection
24 kW
Fuse protection
250 mA (slow-blow) electronic, automatic reset
Continuous current per motor connection
33 Aeff
Continuous power consumption
24.4 kW
Slots for plug-in modules
2
Cooling and mounting type
Cold plate or pass-through mounting

Related documents 8BVI0330HCSA.000-1 Specs