3273720 Phoenix Contact Terminal Blocks

Product Details

• Number of connections
  18
• Rated surge voltage
  6 kV
• Insulating material group
  I
• Note
  Notes on operation The blocks can be bridged with one another via the conductor shaft. For corresponding plug-in bridges, see accessories
• Color
  orange
• Maximum total current
  63 A
• Nominal voltage UN
  800 V
• Result of surge voltage test
  Test passed
• Bending test rotation speed
  10 rpm
• Result of voltage-drop test
  Test passed
• Setpoint
  5 N
• Ageing test for screwless modular terminal block temperature cycles
  192
• Potentials
  1
• Degree of pollution
  3
• Maximum power dissipation for nominal condition
  1.02 W (the value is based on one connection block and is multiplied according to the pin assignment)
• Shock protection test specification
  DIN EN 50274 (VDE 0660-514):2002-11
• Result of the test for mechanical stability of terminal points (5 x conductor connection)
  Test passed
• Bending test conductor cross section/weight
  0.2 mm² / 0.2 kg
• Result of temperature-rise test
  Test passed
• Conductor cross section short circuit testing
  6 mm²
Proof of thermal characteristics (needle flame) effective duration
30 s
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Static insulating material application in cold
-60 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Connection method
Push-in connection
Conductor cross section AWG min.
24
Conductor cross section flexible, with ferrule with plastic sleeve max.
4 mm²
Connection cross sections directly pluggable
0.5 mm² 6 mm² 20 10
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 5.1
27141120
ETIM 2.0
EC000897
Number of levels
1
Flammability rating according to UL 94
V0
Nominal current IN
32 A
Finger protection
guaranteed
Result of power-frequency withstand voltage test
Test passed
Result of tight fit on support
Test passed
Short circuit stability result
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Test spectrum
Service life test category 2, bogie-mounted
Acceleration
30g
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Shock duration
18 ms
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Conductor cross section solid min.
0.5 mm²
Conductor cross section flexible min.
0.2 mm²
Conductor cross section flexible max.
4 mm²
Internal cylindrical gage
A4
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 4.0
27141120
ECLASS 4.1
27141120
UNSPSC 7.0901
39121410
UNSPSC 19.0
39121410
ETIM 7.0
EC000897
Nominal cross section
4 mm²
Insulating material
PA
Overvoltage category
III
Maximum load current
41 A
Back of the hand protection
guaranteed
Bending test turns
135
Tensile test result
Test passed
Result of thermal test
Test passed
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Shock test result
Test passed
Test duration per axis
5 h
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Length
45.7 mm
Connection in acc. with standard
IEC 60947-7-1
Max. AWG conductor cross section, flexible
12
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 11.0
27141120
ECLASS 9.0
27141120
ETIM 4.0
EC000897
UNSPSC 13.2
39121410
Open side panel
No
Power frequency withstand voltage setpoint
2 kV
Result of flexion and pull-out test
Test passed
Tight fit on carrier
NS 35
Short-time current
0.72 kA
Result of aging test
Test passed
ASD level
6.12 (m/s2)2/Hz
Shock form
Half-sine
Surface flammability NFPA 130 (ASTM E 162)
passed
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Width
55.4 mm
Height NS 35/7,5
30.9 mm
Conductor cross section AWG max.
10
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
4 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 10.0.1
27141120
ECLASS 6.0
27141100
ETIM 6.0
EC000897
UNSPSC 11
39121410
UNSPSC 21.0
39121410
Oscillation, broadband noise test result
Test passed
Number of shocks per direction
3
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Stripping length
10 mm ... 12 mm
Conductor cross section solid max.
6 mm²
Min. AWG conductor cross section, flexible
24
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.75 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 5.0
27141120
ECLASS 7.0
27141120
ETIM 3.0
EC000897
UNSPSC 6.01
30211811
UNSPSC 12.01
39121410
UNSPSC 18.0
39121410
UNSPSC 20.0
39121410