3273544 Phoenix Contact Terminal Blocks

Product Details

• Potentials
  1
• Rated surge voltage
  6 kV
• Number of connections
  6
• Insulating material
  PA
• Overvoltage category
  III
• Maximum total current
  63 A
• Nominal current IN
  32 A
• Result of surge voltage test
  Test passed
• Result of the test for mechanical stability of terminal points (5 x conductor connection)
  Test passed
• Number of levels
  1
• Flammability rating according to UL 94
  V0
• Insulating material group
  I
• Nominal voltage UN
  800 V
• Finger protection
  guaranteed
• Bending test rotation speed
  10 rpm
• Result of temperature-rise test
  Test passed
• Short circuit stability result
  Test passed
• Test specification, oscillation, broadband noise
  DIN EN 50155 (VDE 0115-200):2008-03
• Test specification, shock test
  DIN EN 50155 (VDE 0115-200):2008-03
• Note
  Notes on operation The blocks can be bridged with one another via the conductor shaft. For corresponding plug-in bridges, see accessories
Nominal cross section
4 mm²
Degree of pollution
3
Maximum load current
41 A
Back of the hand protection
guaranteed
Result of power-frequency withstand voltage test
Test passed
Bending test conductor cross section/weight
0.2 mm² / 0.2 kg
Tensile test result
Test passed
Short-time current
0.72 kA
Conductor cross section short circuit testing
6 mm²
Oscillation, broadband noise test result
Test passed
Test duration per axis
5 h
Shock test result
Test passed
Surface flammability NFPA 130 (ASTM E 162)
passed
Height NS 35/7,5
32.4 mm
Conductor cross section AWG min.
24
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.75 mm²
Connection cross sections directly pluggable
0.5 mm² 6 mm² 20 10
ECLASS 10.0.1
27141120
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 9.0
27141120
ETIM 3.0
EC000897
UNSPSC 11
39121410
UNSPSC 19.0
39121410
Color
orange
Maximum power dissipation for nominal condition
1.02 W (the value is based on one connection block and is multiplied according to the pin assignment)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Result of flexion and pull-out test
Test passed
Setpoint
5 N
Proof of thermal characteristics (needle flame) effective duration
30 s
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Static insulating material application in cold
-60 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Width
28.6 mm
Conductor cross section AWG max.
10
Max. AWG conductor cross section, flexible
12
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 5.1
27141120
ETIM 2.0
EC000897
UNSPSC 6.01
30211811
UNSPSC 20.0
39121410
Open side panel
No
Power frequency withstand voltage setpoint
2 kV
Result of tight fit on support
Test passed
Result of aging test
Test passed
Result of thermal test
Test passed
ASD level
6.12 (m/s2)2/Hz
Number of shocks per direction
3
Shock duration
18 ms
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Stripping length
10 mm ... 12 mm
Conductor cross section solid min.
0.5 mm²
Min. AWG conductor cross section, flexible
24
Conductor cross section flexible, with ferrule with plastic sleeve max.
4 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 5.0
27141120
ETIM 4.0
EC000897
UNSPSC 7.0901
39121410
UNSPSC 18.0
39121410
Bending test turns
135
Result of voltage-drop test
Test passed
Tight fit on carrier
NS 35
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Ageing test for screwless modular terminal block temperature cycles
192
Acceleration
30g
Test spectrum
Service life test category 2, bogie-mounted
Shock form
Half-sine
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Height NS 15
30.4 mm
Conductor cross section solid max.
6 mm²
Conductor cross section flexible min.
0.2 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
ECLASS 11.0
27141120
ECLASS 4.1
27141120
ETIM 6.0
EC000897
ETIM 7.0
EC000897
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Length
58.1 mm
Connection method
Push-in connection
Conductor cross section flexible max.
4 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
4 mm²
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 4.0
27141120
ECLASS 6.0
27141100
ECLASS 7.0
27141120
UNSPSC 12.01
39121410
UNSPSC 13.2
39121410
UNSPSC 21.0
39121410
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Internal cylindrical gage
A4
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %