3273224 Phoenix Contact Terminal Blocks

Product Details

• Number of levels
  1
• Color
  red
• Overvoltage category
  III
• Maximum total current
  57 A (with 10 mm² conductor cross section)
• Open side panel
  No
• Power frequency withstand voltage setpoint
  1.89 kV
• Bending test conductor cross section/weight
  0.5 mm² / 0.3 kg
• Result of voltage-drop test
  Test passed
• Short-time current
  1.2 kA
• Note
  The max. load current must not be exceeded by the total current of all connected conductors.
• Rated surge voltage
  8 kV
• Degree of pollution
  3
• Nominal current IN
  41 A (with 6 mm² conductor cross section)
• Finger protection
  guaranteed
• Bending test turns
  135
• Setpoint
  5 N
• Short circuit stability result
  Test passed
• Result of aging test
  Test passed
• Test specification, oscillation, broadband noise
  DIN EN 50155 (VDE 0115-200):2008-03
• Test specification, shock test
  DIN EN 50155 (VDE 0115-200):2008-03
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Height NS 35/7,5
30.9 mm
Conductor cross section flexible min.
0.5 mm²
Connection cross sections directly pluggable
1 mm² 10 mm²
Internal cylindrical gage
A3
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 6.0
27141100
UNSPSC 11
39121410
UNSPSC 19.0
39121410
Potentials
1
Nominal cross section feed-in
6 mm²
Insulating material
PA
Maximum power dissipation for nominal condition
1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
Back of the hand protection
guaranteed
Result of power-frequency withstand voltage test
Test passed
Tight fit on carrier
NS 35
Conductor cross section short circuit testing
10 mm²
Ageing test for screwless modular terminal block temperature cycles
192
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Shock test result
Test passed
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Connection method
Push-in connection
Conductor cross section AWG min.
20
Conductor cross section solid max.
10 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Connection
Feed-in stage
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 5.1
27141120
ECLASS 5.0
27141120
ECLASS 9.0
27141120
UNSPSC 7.0901
39121410
UNSPSC 20.0
39121410
Nominal cross section
2.5 mm²
Maximum load current
57 A (with 10 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Result of flexion and pull-out test
Test passed
Result of tight fit on support
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Result of thermal test
Test passed
Test spectrum
Service life test category 2, bogie-mounted
ASD level
6.12 (m/s2)2/Hz
Number of shocks per direction
3
Surface flammability NFPA 130 (ASTM E 162)
passed
Length
45.7 mm
Connection in acc. with standard
IEC 60947-7-1
Min. AWG conductor cross section, flexible
20
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Value
1 mm²
ECLASS 10.0.1
27141120
ECLASS 4.1
27141121
ETIM 3.0
EC000897
ETIM 7.0
EC000897
UNSPSC 18.0
39121410
UNSPSC 21.0
39121410
Number of connections
13
Flammability rating according to UL 94
V0
Insulating material group
I
Nominal voltage UN
690 V
Result of surge voltage test
Test passed
Bending test rotation speed
10 rpm
Tensile test result
Test passed
Result of temperature-rise test
Test passed
Oscillation, broadband noise test result
Test passed
Acceleration
30g
Shock duration
18 ms
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Conductor cross section solid min.
1 mm²
Conductor cross section flexible max.
10 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 11.0
27141120
UNSPSC 6.01
30211811
ETIM 4.0
EC000897
UNSPSC 12.01
39121410
Proof of thermal characteristics (needle flame) effective duration
30 s
Test directions
X-, Y- and Z-axis (pos. and neg.)
Test duration per axis
5 h
Shock form
Half-sine
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Width
41 mm
Stripping length
10 mm ... 12 mm
Conductor cross section AWG max.
8
Max. AWG conductor cross section, flexible
10
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 4.0
27141121
ECLASS 7.0
27141120
ETIM 6.0
EC000897
UNSPSC 13.2
39121410