3273082 Phoenix Contact Terminal Blocks

Product Details

• Number of connections
  7
• Nominal cross section feed-in
  6 mm²
• Rated surge voltage
  8 kV
• Insulating material group
  I
• Maximum total current
  57 A (with 10 mm² conductor cross section)
• Open side panel
  No
• Back of the hand protection
  guaranteed
• Result of power-frequency withstand voltage test
  Test passed
• Bending test rotation speed
  10 rpm
• Tensile test result
  Test passed
• Tight fit on carrier
  NS 35
• Short circuit stability result
  Test passed
• Conductor cross section short circuit testing
  10 mm²
• Ageing test for screwless modular terminal block temperature cycles
  192
• Test spectrum
  Service life test category 2, bogie-mounted
• Test frequency
  f1 = 5 Hz to f2 = 250 Hz
• Shock test result
  Test passed
• Test specification, shock test
  DIN EN 50155 (VDE 0115-200):2008-03
• Relative insulation material temperature index (Elec., UL 746 B)
  130 °C
• Surface flammability NFPA 130 (ASTM E 162)
  passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Number of levels
1
Potentials
1
Color
violet
Degree of pollution
3
Overvoltage category
III
Nominal voltage UN
690 V
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Finger protection
guaranteed
Power frequency withstand voltage setpoint
1.89 kV
Bending test turns
135
Result of tight fit on support
Test passed
Setpoint
5 N
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Result of thermal test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Oscillation, broadband noise test result
Test passed
Acceleration
30g
Test duration per axis
5 h
Shock duration
18 ms
Number of shocks per direction
3
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Height NS 15
30.4 mm
Conductor cross section solid max.
10 mm²
Min. AWG conductor cross section, flexible
20
Connection cross sections directly pluggable
1 mm² 10 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 11.0
27141120
ECLASS 5.0
27141120
UNSPSC 6.01
30211811
UNSPSC 7.0901
39121410
UNSPSC 19.0
39121410
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Height NS 35/7,5
32.4 mm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section flexible min.
0.5 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 9.0
27141120
ETIM 4.0
EC000897
UNSPSC 11
39121410
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Nominal cross section
2.5 mm²
Insulating material
PA
Flammability rating according to UL 94
V0
Maximum power dissipation for nominal condition
1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
Maximum load current
57 A (with 10 mm² conductor cross section)
Nominal current IN
41 A (with 6 mm² conductor cross section)
Result of surge voltage test
Test passed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Result of flexion and pull-out test
Test passed
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Result of voltage-drop test
Test passed
Result of temperature-rise test
Test passed
Short-time current
1.2 kA
Result of aging test
Test passed
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
ASD level
6.12 (m/s2)2/Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Shock form
Half-sine
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Width
28.6 mm
Stripping length
10 mm ... 12 mm
Conductor cross section AWG max.
8
Conductor cross section flexible max.
10 mm²
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Connection
Feed-in stage
Value
1 mm²
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 4.1
27141121
ECLASS 7.0
27141120
ETIM 6.0
EC000897
UNSPSC 13.2
39121410
UNSPSC 21.0
39121410
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 10.0.1
27141120
ECLASS 6.0
27141100
ETIM 7.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 20.0
39121410
Length
58.1 mm
Connection method
Push-in connection
Conductor cross section solid min.
1 mm²
Conductor cross section AWG min.
20
Max. AWG conductor cross section, flexible
10
Internal cylindrical gage
A3
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 4.0
27141121
ECLASS 5.1
27141120
ETIM 3.0
EC000897
UNSPSC 18.0
39121410