1211221 Phoenix Contact Electrical Wires & Cables

Product Details

• Standards/regulations
  DIN EN 60751
• Note on the connection method
  Crimp connection, cannot be disconnected
• Bore dimensions
  117.65 mm x 90 mm, 117.65 mm x 83 mm
• Degree of protection
  IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
• Number of power contacts
  3 (PE, DC+, DC-)
• Resistor coding
  4.7 kΩ (between PE and PP)
• Application
  For charging with direct current (DC)
• Note
  A protective cap is supplied as standard for the DC contacts.
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Type of charging current
  DC
• Rated voltage for signal contacts
  30 V AC
• Insulation resistance of neighboring contacts
  > 200 MΩ
• Withdrawal force
  < 100 N
• Screws included in the scope of delivery
  none
• Flammability rating
  V0
• Cable resistance
  ≤ 37.1 Ω/km
• Cable weight
  7 kg/km
• Number of positions of theconnectors
  4
• Service life insertion cycles
  > 10000 load cycles
• Type of sensor
  Pt 1000
Type
Locking actuator right
Charging standard
CCS type 2
Ambient temperature (operation)
-40 °C ... 80 °C
Maximum charging power
200 kW
Rated voltage for power contacts
1000 V DC
Insertion/withdrawal cycles
> 10000
Mounting hole diameter
6.80 mm (ø)
Required mounting screws
M6
Outer sheath, material
PVC
Operating voltage
12 V (Typical power supply at the motor)
Max. dwell time with reverse current
1 s
Pause time after entry or exit path
3 s
Mechanical emergency release
available
Design
Generation 4
Width
108 mm
Height
140.25 mm
Max. altitude
4000 m (above sea level)
Rated current of power contacts
200 A DC
Number of signal contacts
2 (CP, PP)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Design line
Generation 4
Material surface of contacts
Ag
External cable diameter
1.6 mm -0.2 mm
Single wire, color
black PP/CS
Maximum voltage for locking detection
12 V
Recommended adaptation time
600 ms
Temperature range
-40 °C ... 130 °C
Shutdown temperature
90 °C
Charging mode
Mode 4
Depth
133.5 mm
Conductor length
2 m (DC cables)
Rated current for signal contacts
2 A
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Mounting position of the locking actuator
Right-side
Housing color
black
Customer variations
On request
Cable structure
4 x 0.5 mm²
External sheath, color
Green-yellow
Typical motor current for locking
0.25 A
Lock recognition
available
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Tolerance at the sensor with the recommended measured current
±3K
ECLASS 11.0
27144706
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Insertion force
< 100 N
Material
Plastic
Locking type
Locking in the inserted state with a locking mechanism
Minimum bending radius
15 mm
Possible power supply range at the motor
9 V ... 16 V
Reverse current of the motor
max. 1.5 A
Cable length
1 m
Temperature coefficient (TCR)
3850 ppm/K
ECLASS 9.0
27144706
Long-term stability (max. R0-Drift)
≤ 0.1 % (After 1000 hours at 130°C)
ECLASS 10.0.1
27144706