1211220 Phoenix Contact Electrical Wires & Cables

1211220 Product Details

• Type
  Locking actuator right
• Note
  A protective cap is supplied as standard for the DC contacts.
• Charging mode
  Mode 4
• Depth
  133.5 mm
• Rated current of power contacts
  250 A DC
• Insulation resistance of neighboring contacts
  > 200 MΩ
• Insertion force
  < 100 N
• Customer variations
  On request
• Standards/regulations
  DIN EN 60751
• Conductor length
  2 m (DC cables)
• Maximum charging power
  250 kW
• Number of signal contacts
  2 (CP, PP)
• Withdrawal force
  < 100 N
• Mounting position of the locking actuator
  Right-side
• Flammability rating
  V0
• Cable structure
  4 x 0.5 mm²
• External cable diameter
  1.6 mm -0.2 mm
• Maximum voltage for locking detection
  30 V
• Design
  Generation 4
• Note on the connection method
  Crimp connection, cannot be disconnected
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Max. altitude
4000 m (above sea level)
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Mounting hole diameter
6.80 mm (ø)
Housing color
black
Cable resistance
≤ 37.1 Ω/km
Operating voltage
24 V (Typical power supply at the motor)
Typical motor current for locking
0.05 A
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Shutdown temperature
90 °C
ECLASS 11.0
27144706
Application
For charging with direct current (DC)
Height
140.25 mm
Ambient temperature (operation)
-30 °C ... 50 °C
Type of charging current
DC
Rated voltage for power contacts
1000 V DC
Resistor coding
4.7 kΩ (between PE and PP)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Required mounting screws
M6
Material
Plastic
Cable weight
7 kg/km
Max. dwell time with reverse current
1 s
Pause time after entry or exit path
3 s
Lock recognition
available
Temperature coefficient (TCR)
3850 ppm/K
Charging standard
CCS type 2
Width
108 mm
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of power contacts
3 (PE, DC+, DC-)
Rated current for signal contacts
2 A
Rated voltage for signal contacts
30 V AC
Insertion/withdrawal cycles
> 10000
Screws included in the scope of delivery
none
Design line
Generation 4
Locking type
Locking in the inserted state with a locking mechanism
Outer sheath, material
PVC
Minimum bending radius
15 mm
Single wire, color
black PP/CS
Reverse current of the motor
max. 0.5 A
Type of sensor
Pt 1000
Temperature range
-40 °C ... 130 °C
ECLASS 9.0
27144706
Material surface of contacts
Ag
External sheath, color
Green-yellow
Number of positions of theconnectors
4
Possible power supply range at the motor
22 V ... 26 V
Cable length
0.5 m
Tolerance at the sensor with the recommended measured current
±3K
ECLASS 10.0.1
27144706
Recommended adaptation time
600 ms
Mechanical emergency release
available
Long-term stability (max. R0-Drift)
≤ 0.1 % (After 1000 hours at 130°C)
Resistance range
650 Ω ... 1450 Ω

Product condition