1211212 Phoenix Contact Electrical Wires & Cables

Product Details

• Type
  Locking actuator right
• Height
  130.4 mm
• Depth
  128.4 mm
• Ambient temperature (operation)
  -30 °C ... 50 °C
• Number of phases
  3
• Rated voltage for signal contacts
  30 V AC
• Temperature monitoring
  AC contacts: PTC chain (DIN˽EN˽60738-1)
• Required mounting screws
  M6
• Flammability rating
  V0
• External sheath, color
  Green-yellow
• Maximum voltage for locking detection
  30 V
• Max. dwell time with reverse current
  1 s
• Lock recognition
  available
• Tolerance at the sensor with the recommended measured current
  ±5K
• ECLASS 9.0
  27144706
• Design
  Generation 4
• Note on the connection method
  Crimp connection, cannot be disconnected
• Bore dimensions
  117.65 mm x 90 mm, 117.65 mm x 83 mm
• Degree of protection
  IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
• Rated voltage for power contacts
  480 V AC
Insulation resistance of neighboring contacts
> 200 MΩ
Resistor coding
4.7 kΩ (between PE and PP)
Insertion force
< 100 N
Mounting hole diameter
6.80 mm (ø)
Material
Plastic
Material surface of contacts
Ag
Outer sheath, material
PVC
Operating voltage
24 V (Typical power supply at the motor)
Possible power supply range at the motor
22 V ... 26 V
Pause time after entry or exit path
3 s
Mechanical emergency release
available
Cable length
0.5 m
Resistance range
650 Ω ... 1450 Ω
Charging standard
CCS type 2
Max. altitude
4000 m (above sea level)
Type of charging current
DC, AC 3-phase
Number of signal contacts
2 (CP, PP)
Insertion/withdrawal cycles
> 10000
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Screws included in the scope of delivery
none
Customer variations
On request
Cable resistance
≤ 37.1 Ω/km
Cable weight
7 kg/km
Minimum bending radius
15 mm
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 11.0
27144706
Standards/regulations
DIN EN 60751
Note
A protective cap is supplied as standard for the DC and AC contacts.
Conductor length
2 m (AC cables)
Maximum charging power
200 kW
Number of power contacts
7 (L1, L2, L3, N, PE, DC+, DC-)
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Withdrawal force
< 100 N
Design line
Generation 4
External cable diameter
1.6 mm -0.2 mm
Number of positions of theconnectors
4
Reverse current of the motor
max. 0.5 A
Recommended adaptation time
600 ms
Temperature range
-40 °C ... 130 °C
ECLASS 10.0.1
27144706
Application
For charging with alternating current (AC) and with direct current (DC)
Charging mode
Mode 2, 3, 4
Width
108 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Rated current of power contacts
32 A AC
Rated current for signal contacts
2 A
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Mounting position of the locking actuator
Right-side
Housing color
black
Cable structure
4 x 0.5 mm²
Locking type
Locking in the inserted state with a locking mechanism
Single wire, color
black PP/CS
Typical motor current for locking
0.05 A
Type of sensor
Pt 1000
China RoHS
Environmentally Friendly Use Period = 10;