1211217 Phoenix Contact Electrical Wires & Cables

Product Details

• Standards/regulations
  DIN EN 60751
• Height
  140.25 mm
• Max. altitude
  4000 m (above sea level)
• Number of power contacts
  3 (PE, DC+, DC-)
• Rated voltage for signal contacts
  30 V AC
• Resistor coding
  4.7 kΩ (between PE and PP)
• Mounting position of the locking actuator
  Right-side
• Design line
  Generation 4
• Application
  For charging with direct current (DC)
• Note
  A protective cap is supplied as standard for the DC contacts.
• Depth
  133.5 mm
• Conductor length
  2 m (DC cables)
• Maximum charging power
  200 kW
• Number of signal contacts
  2 (CP, PP)
• Temperature measurement
  DC contacts: 2x PT1000 (DIN EN 60751)
• Screws included in the scope of delivery
  none
• Material surface of contacts
  Ag
• Outer sheath, material
  PVC
• Single wire, color
  black PP/CS
• Max. dwell time with reverse current
  1 s
Service life insertion cycles
> 10000 load cycles
Temperature range
-40 °C ... 130 °C
ECLASS 11.0
27144706
Charging standard
CCS type 2
Width
108 mm
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Rated voltage for power contacts
1000 V DC
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Insertion force
< 100 N
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Mounting hole diameter
6.80 mm (ø)
Customer variations
On request
Cable structure
4 x 0.5 mm²
Minimum bending radius
15 mm
Maximum voltage for locking detection
30 V
Reverse current of the motor
max. 0.5 A
Tolerance at the sensor with the recommended measured current
±3K
Type
Locking actuator right
Charging mode
Mode 4
Note on the connection method
Crimp connection, cannot be disconnected
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Type of charging current
DC
Rated current for signal contacts
2 A
Insertion/withdrawal cycles
> 10000
Required mounting screws
M6
Flammability rating
V0
External cable diameter
1.6 mm -0.2 mm
Cable resistance
≤ 37.1 Ω/km
Operating voltage
24 V (Typical power supply at the motor)
Typical motor current for locking
0.05 A
Cable length
0.5 m
Mechanical emergency release
available
Shutdown temperature
90 °C
Design
Generation 4
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Ambient temperature (operation)
-30 °C ... 50 °C
Rated current of power contacts
200 A DC
Insulation resistance of neighboring contacts
> 200 MΩ
Withdrawal force
< 100 N
Housing color
black
Material
Plastic
Cable weight
7 kg/km
Possible power supply range at the motor
22 V ... 26 V
Pause time after entry or exit path
3 s
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Type of sensor
Pt 1000
Long-term stability (max. R0-Drift)
≤ 0.1 % (After 1000 hours at 130°C)
ECLASS 9.0
27144706
Locking type
Locking in the inserted state with a locking mechanism
External sheath, color
Green-yellow
Number of positions of theconnectors
4
Recommended adaptation time
600 ms
Lock recognition
available
Temperature coefficient (TCR)
3850 ppm/K
Resistance range
650 Ω ... 1450 Ω
ECLASS 10.0.1
27144706