1211595 Phoenix Contact Electrical Wires & Cables

1211595 Product Details

• Note on the connection method
  Crimp connection, cannot be disconnected
• Depth
  122.8 mm
• Maximum charging power
  200 kW
• Rated voltage for signal contacts
  30 V AC
• Insertion/withdrawal cycles
  > 10000
• Restrictions to mounting position
  Only 0 to 90 degree frontal inclination possible, see figure
• Screws included in the scope of delivery
  none
• Flammability rating
  V0
• Cable weight
  7 kg/km
• Maximum voltage for locking detection
  12 V
• Cable length
  1 m
• Application
  For charging with direct current (DC)
• Height
  151.2 mm
• Ambient temperature (operation)
  -40 °C ... 80 °C
• Degree of protection
  IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
• Rated current of power contacts
  200 A DC
• Number of signal contacts
  2 (CP, CS)
• Withdrawal force
  < 100 N
• Required mounting screws
  M6
• Cable structure
  4 x 0.5 mm²
Minimum bending radius
15 mm
Operating voltage
12 V (Typical power supply at the motor)
Max. dwell time with reverse current
1 s
Lock recognition
available
Temperature coefficient (TCR)
3850 ppm/K
ECLASS 11.0
27144706
Standards/regulations
DIN EN 60751
Charging mode
Mode 4
Conductor length
2 m (DC cables)
Type of charging current
DC
Rated current for signal contacts
2 A
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Mounting hole diameter
6.80 mm (ø)
Design line
Generation 4
Material
Plastic
External sheath, color
Green-yellow
Number of positions of theconnectors
4
Reverse current of the motor
max. 1.5 A
Recommended adaptation time
600 ms
Type of sensor
Pt 1000
Long-term stability (max. R0-Drift)
≤ 0.1 % (After 1000 hours at 130°C)
Type
Locking actuator top
Charging standard
CCS type 1
Width
108 mm
Max. altitude
4000 m (above sea level)
Number of power contacts
5 (L1, N, PE, DC+, DC-)
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Insertion force
< 100 N
Mounting position of the locking actuator
Top center
Housing color
black
Locking type
Locking in the inserted state with a locking mechanism
Outer sheath, material
PVC
Possible power supply range at the motor
9 V ... 16 V
Typical motor current for locking
0.25 A
Tolerance at the sensor with the recommended measured current
±3K
Shutdown temperature
90 °C
Design
Generation 4
Note
A protective cap is supplied as standard for the DC contacts.
Bore dimensions
117.6 mm x 90 mm, 117.6 mm x 83 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Number of phases
1
Rated voltage for power contacts
1000 V DC
Insulation resistance of neighboring contacts
> 200 MΩ
Resistor coding
2.7 kΩ (between PE and CS)
Customer variations
On request
Material surface of contacts
Ag
External cable diameter
1.6 mm -0.2 mm
Cable resistance
≤ 37.1 Ω/km
Single wire, color
black PP/CS
Pause time after entry or exit path
3 s
Mechanical emergency release
available
Temperature range
-40 °C ... 130 °C
ECLASS 9.0
27144706
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 10.0.1
27144706

Product condition