1211606 Phoenix Contact Electrical Wires & Cables

1211606 Product Details

• Application
  For charging with direct current (DC)
• Type
  Locking actuator top
• Charging mode
  Mode 4
• Bore dimensions
  117.6 mm x 90 mm, 117.6 mm x 83 mm
• Width
  108 mm
• Type of charging current
  DC
• Maximum charging power
  250 kW
• Rated voltage for power contacts
  1000 V DC
• Insertion force
  < 100 N
• Screws included in the scope of delivery
  none
• Housing color
  black
• External cable diameter
  1.6 mm -0.2 mm
• External sheath, color
  Green-yellow
• Possible power supply range at the motor
  9 V ... 16 V
• Service life insertion cycles
  > 10000 load cycles
• Lock recognition
  available
• Number of power contacts
  5 (L1, N, PE, DC+, DC-)
• Charging standard
  CCS type 1
• Height
  151.2 mm
• Number of signal contacts
  2 (CP, CS)
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Rated voltage for signal contacts
30 V AC
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Customer variations
On request
Cable structure
4 x 0.5 mm²
Cable resistance
≤ 37.1 Ω/km
Maximum voltage for locking detection
12 V
Max. dwell time with reverse current
1 s
Reverse current of the motor
max. 1.5 A
Mechanical emergency release
available
Temperature coefficient (TCR)
3850 ppm/K
Design
Generation 4
Depth
122.8 mm
Ambient temperature (operation)
-40 °C ... 80 °C
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Rated current for signal contacts
2 A
Withdrawal force
< 100 N
Mounting hole diameter
6.80 mm (ø)
Flammability rating
V0
Locking type
Locking in the inserted state with a locking mechanism
Minimum bending radius
15 mm
Single wire, color
black PP/CS
Recommended adaptation time
600 ms
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 11.0
27144706
Standards/regulations
DIN EN 60751
Note
A protective cap is supplied as standard for the DC contacts.
Conductor length
2 m (DC cables)
Max. altitude
4000 m (above sea level)
Rated current of power contacts
250 A DC
Resistor coding
2.7 kΩ (between PE and CS)
Mounting position of the locking actuator
Top center
Required mounting screws
M6
Material
Plastic
Outer sheath, material
PVC
Operating voltage
12 V (Typical power supply at the motor)
Typical motor current for locking
0.25 A
Cable length
1 m
Type of sensor
Pt 1000
Long-term stability (max. R0-Drift)
≤ 0.1 % (After 1000 hours at 130°C)
Shutdown temperature
90 °C
Note on the connection method
Crimp connection, cannot be disconnected
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Number of phases
1
Insulation resistance of neighboring contacts
> 200 MΩ
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Insertion/withdrawal cycles
> 10000
Design line
Generation 4
Material surface of contacts
Ag
Cable weight
7 kg/km
Number of positions of theconnectors
4
Pause time after entry or exit path
3 s
Tolerance at the sensor with the recommended measured current
±3K
ECLASS 9.0
27144706
Temperature range
-40 °C ... 130 °C
ECLASS 10.0.1
27144706

Product condition