8V1016.50-2 B&R Electronic Components
Part#:8V1016.50-2
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
ACOPOS servo drive, 3x 110-230 V / 1x 110-230 V, 3.6 A, 0.7 kW, integrated line filter, braking resistor and electronic safe restart interlock
Check out the 8V1016.50-2 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight2.5 kg
- Temperature Operation Maximum 55°C
- Terminal connection cross section Approbation data UL/C-UL-US 30 to 10 AWG
- Terminal connection cross section Approbation data CSA 28 to 10 AWG
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 20 kHz No reduction
- Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves 0.25 to 4 mm²
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 10 kHz No reduction
- Dimensions Height 257 mm
- Dimensions Width 58.5 mm
- Energy efficiency (IE classification) Efficiency data IE2 (10,25) 5.3% ; IE2 (50,25) 5.9% ; IE2 (10,50) 5.4% ; IE2 (50,50) 6.7% ; IE2 (90,50) 9% ; IE2 (10,100) 6.3% ; IE2 (50,100) 9.7% ; IE2 (90,100) 16.5%
- Temperature Operation Nominal 5 to 40°C
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 20 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 5 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 5 kHz No reduction
- Dimensions Depth 220 mm
- Relative humidity Transport Max. 95% at 40°C
- Relative humidity Storage 5 to 95%
- Relative humidity Operation 5 to 85%
- Temperature Storage -25 to 55°C
- Installation elevation above sea level Nominal 0 to 500 m
- Temperature Transport -25 to 70°C
- Installation elevation above sea level Maximum 2000 m
- Permissible mounting orientations Standing horizontally No
- Permissible mounting orientations Hanging vertically Yes
- Permissible mounting orientations Horizontal, face up Yes
- Energy efficiency (IE classification) Nominal losses in standby mode 12.5 W
- Switching delay Falling edge 53 µs ±0.5 µs (digitally filtered)
- Switching delay Rising edge 52 µs ±0.5 µs (digitally filtered)
- Switching delay Enable 1 → 0, PWM off Max. 2.0 ms
- Protective measures Overload protection Yes
- Switching threshold High >15 V
- Input voltage Maximum 30 VDC
- Input voltage Nominal 24 VDC
- Switching delay Enable 0 → 1, ready for PWM Max. 100 µs
- Switching threshold Low <5 V
- Electrical isolation Input - Input No
- Electrical isolation Input - ACOPOS Yes
- Protective measures Short-circuit and ground fault protection Yes
- Reduction of continuous current depending on installation elevation Starting at 500 m above sea level 0.36 Aeff per 1000 m
- Certifications EAC Yes
- Certifications UL cULus E225616; Power conversion equipment
- Certifications KC Yes
- Degree of protection per EN 60529 IP20
- Certifications Functional safety Yes
- Certifications CE Yes
- Overvoltage category per EN 61800-5-1 II
- OSSD signal connections Not permitted
- Modulation compared to ground potential Max. ±38 V
- Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
- Input current at nominal voltage Approx. 4 mA
- Circuit Sink
- Switching delay Max. 2.0 ms
- Peak power output 1.9 kW
- Continuous power 130 W
- Max. number of switching cycles Unlimited since implemented electronically
- Max. output frequency 598 Hz
- Max. motor line length 15 m
- Response threshold for open-circuit monitoring Approx. 245 mA
- Max. output current 1.3 A
- Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
- Possible switching frequencies 5 / 10 / 20 kHz
- Quantity 1
- Peak current 12 Aeff
- Continuous current 3.6 Aeff
- Nominal switching frequency 10 kHz
- Current consumption Max. 1.47 A + Current for motor holding brake
- Input capacitance 5600 µF
- DC bus capacitance 2040 µF
- Input voltage 24 VDC +25% / -20%
- Power dissipation at device nominal power without braking resistor 110 W
- Slots for plug-in modules 3
- Inrush current 5 A (at 230 VAC)
- Switch-on interval >10 s
- Permissible network configurations TT, TN
- Frequency 50 / 60 Hz ±4%
- Installed load Max. 2.1 kVA
- B&R ID code 0x18D7
- Integrated line filter per EN 61800-3, category C3 Yes
- Mains input voltage 3x 110 VAC to 230 VAC ±10% or 1x 110 VAC to 230 VAC ±10%
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨