8V1010.001-2 B&R Electronic Components
Part#:8V1010.001-2
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
ACOPOS servo drive, 3x 400-480 V, 1.0 A, 0.45 kW, coated, integrated line filter, braking resistor and electronic safe restart interlock
Check out the 8V1010.001-2 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight2.5 kg
- Temperature Operation Maximum 55°C
- Temperature Operation Nominal 5 to 40°C
- Dimensions Depth 220 mm
- Terminal connection cross section Approbation data UL/C-UL-US 30 to 10 AWG
- Terminal connection cross section Approbation data CSA 28 to 10 AWG
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 20 kHz 0.13 Aeff per °C (starting at 45°C)
- Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves 0.25 to 4 mm²
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 5 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 5 kHz No reduction
- Dimensions Width 58.5 mm
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 20 kHz No reduction
- Dimensions Height 257 mm
- Relative humidity Transport Max. 95% at 40°C
- Relative humidity Storage 5 to 95%
- Permissible mounting orientations Hanging vertically Yes
- Relative humidity Operation 5 to 85%
- Installation elevation above sea level Maximum 2000 m
- Temperature Storage -25 to 55°C
- Permissible mounting orientations Standing horizontally No
- Temperature Transport -25 to 70°C
- Permissible mounting orientations Horizontal, face up Yes
- Installation elevation above sea level Nominal 0 to 500 m
- Energy efficiency (IE classification) Nominal losses in standby mode 12.5 W
- Switching delay Falling edge 53 µs ±0.5 µs (digitally filtered)
- Energy efficiency (IE classification) Efficiency data IE2 (10,25) 6.6% ; IE2 (50,25) 6.7% ; IE2 (10,50) 6.6% ; IE2 (50,50) 6.7% ; IE2 (90,50) 6.8% ; IE2 (10,100) 6.9% ; IE2 (50,100) 7% ; IE2 (90,100) 7.3%
- Switching delay Enable 0 → 1, ready for PWM Max. 100 µs
- Switching delay Rising edge 52 µs ±0.5 µs (digitally filtered)
- Switching delay Enable 1 → 0, PWM off Max. 2.0 ms
- Switching threshold Low <5 V
- Switching threshold High >15 V
- Input voltage Maximum 30 VDC
- Input voltage Nominal 24 VDC
- Electrical isolation Input - Input No
- Electrical isolation Input - ACOPOS Yes
- Protective measures Short-circuit and ground fault protection Yes
- Certifications EAC Yes
- Certifications UL cULus E225616; Power conversion equipment
- Reduction of continuous current depending on installation elevation Starting at 500 m above sea level 0.1 Aeff per 1000 m
- Certifications KC Yes
- Protective measures Overload protection Yes
- Certifications Functional safety Yes
- Certifications CE Yes
- Degree of protection per EN 60529 IP20
- Overvoltage category per EN 61800-5-1 II
- Modulation compared to ground potential Max. ±38 V
- Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
- Discharge capacitance 550 nF
- Circuit Sink
- Switching delay Max. 2.0 ms
- OSSD signal connections Not permitted
- Input current at nominal voltage Approx. 4 mA
- Continuous power 130 W
- Max. number of switching cycles Unlimited since implemented electronically
- Peak power output 2 kW
- Possible switching frequencies 5 / 10 / 20 kHz
- Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
- Max. output current 1.3 A
- Max. output frequency 598 Hz
- Response threshold for open-circuit monitoring Approx. 245 mA
- Max. motor line length 15 m
- Nominal switching frequency 10 kHz
- Peak current 2.8 Aeff
- Current consumption Max. 1.47 A + Current for motor holding brake
- Continuous current 1 Aeff
- Quantity 1
- Input capacitance 5600 µF
- DC bus capacitance 165 µF
- Permissible network configurations TT, TN
- Integrated line filter per EN 61800-3, category C3 Yes
- Power dissipation at device nominal power without braking resistor 80 W
- Input voltage 24 VDC +25% / -20%
- Frequency 50 / 60 Hz ±4%
- B&R ID code 0xA6D4
- Note Variant with partially coated printed circuit boards
- Slots for plug-in modules 3
- Switch-on interval >10 s
- Mains input voltage 3x 400 VAC to 480 VAC ±10%; 3x 230 VAC ±10%
- Installed load Max. 1.35 kVA
- Inrush current 2 A (at 400 VAC)
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨