8V1010.501-2 B&R Electronic Components
Part#:8V1010.501-2
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
ACOPOS servo drive, 3x 110-230 V / 1x 110-230 V, 2.3 A, 0.45 kW, coated, integrated line filter, braking resistor and electronic safe restart interlock
Check out the 8V1010.501-2 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight2.5 kg
- Temperature Operation Maximum 55°C
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 20 kHz No reduction
- Terminal connection cross section Approbation data CSA 28 to 10 AWG
- Temperature Operation Nominal 5 to 40°C
- Terminal connection cross section Approbation data UL/C-UL-US 30 to 10 AWG
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 20 kHz No reduction
- Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves 0.25 to 4 mm²
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 5 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 10 kHz No reduction
- Dimensions Depth 220 mm
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 10 kHz No reduction
- Dimensions Height 257 mm
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 5 kHz No reduction
- Relative humidity Transport Max. 95% at 40°C
- Relative humidity Operation 5 to 85%
- Relative humidity Storage 5 to 95%
- Temperature Storage -25 to 55°C
- Dimensions Width 58.5 mm
- Installation elevation above sea level Maximum 2000 m
- Temperature Transport -25 to 70°C
- Installation elevation above sea level Nominal 0 to 500 m
- Permissible mounting orientations Horizontal, face up Yes
- Permissible mounting orientations Hanging vertically Yes
- Switching delay Enable 0 → 1, ready for PWM Max. 100 µs
- Permissible mounting orientations Standing horizontally No
- Switching delay Rising edge 52 µs ±0.5 µs (digitally filtered)
- Energy efficiency (IE classification) Nominal losses in standby mode 12.5 W
- Switching delay Falling edge 53 µs ±0.5 µs (digitally filtered)
- Energy efficiency (IE classification) Efficiency data IE2 (10,25) 7% ; IE2 (50,25) 7.6% ; IE2 (10,50) 7.1% ; IE2 (50,50) 8.2% ; IE2 (90,50) 10.4% ; IE2 (10,100) 7.8% ; IE2 (50,100) 10.9% ; IE2 (90,100) 17.1%
- Switching delay Enable 1 → 0, PWM off Max. 2.0 ms
- Switching threshold High >15 V
- Switching threshold Low <5 V
- Input voltage Maximum 30 VDC
- Input voltage Nominal 24 VDC
- Electrical isolation Input - Input No
- Electrical isolation Input - ACOPOS Yes
- Certifications KC Yes
- Protective measures Overload protection Yes
- Protective measures Short-circuit and ground fault protection Yes
- Reduction of continuous current depending on installation elevation Starting at 500 m above sea level 0.23 Aeff per 1000 m
- Certifications UL cULus E225616; Power conversion equipment
- Certifications CE Yes
- Certifications EAC Yes
- Certifications Functional safety Yes
- Degree of protection per EN 60529 IP20
- Modulation compared to ground potential Max. ±38 V
- Switching delay Max. 2.0 ms
- Input current at nominal voltage Approx. 4 mA
- Circuit Sink
- Discharge capacitance 330 nF
- Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
- Overvoltage category per EN 61800-5-1 II
- OSSD signal connections Not permitted
- Max. output current 1.3 A
- Response threshold for open-circuit monitoring Approx. 245 mA
- Continuous power 130 W
- Nominal switching frequency 10 kHz
- Max. number of switching cycles Unlimited since implemented electronically
- Max. motor line length 15 m
- Peak power output 1.9 kW
- Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
- Possible switching frequencies 5 / 10 / 20 kHz
- Current consumption Max. 1.47 A + Current for motor holding brake
- Continuous current 2.3 Aeff
- Input capacitance 5600 µF
- Input voltage 24 VDC +25% / -20%
- Max. output frequency 598 Hz
- Peak current 7.8 Aeff
- Quantity 1
- DC bus capacitance 2040 µF
- Power dissipation at device nominal power without braking resistor 80 W
- Frequency 50 / 60 Hz ±4%
- Integrated line filter per EN 61800-3, category C3 Yes
- Mains input voltage 3x 110 VAC to 230 VAC ±10% or 1x 110 VAC to 230 VAC ±10%
- Slots for plug-in modules 3
- Permissible network configurations TT, TN
- Note Variant with partially coated printed circuit boards
- B&R ID code 0xA6D5
- Installed load Max. 1.35 kVA
- Switch-on interval >10 s
- Inrush current 5 A (at 230 VAC)
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨