8V1022.00-2 B&R Electronic Components
Part#:8V1022.00-2
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
ACOPOS servo drive, 3x 400-480 V, 2.2 A, 1 kW, integrated line filter, braking resistor and electronic safe restart interlock
Check out the 8V1022.00-2 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight4 kg
- Terminal connection cross section Approbation data CSA 28 to 10 AWG
- Temperature Operation Nominal 5 to 40°C
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 20 kHz 0.13 Aeff per °C (starting at 51°C)
- Terminal connection cross section Approbation data UL/C-UL-US 30 to 10 AWG
- Temperature Operation Maximum 55°C
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 20 kHz No reduction
- Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves 0.25 to 4 mm²
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 5 kHz No reduction
- Dimensions Depth 235.5 mm
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 5 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 10 kHz No reduction
- Dimensions Height 375 mm
- Dimensions Width 70.5 mm
- Relative humidity Operation 5 to 85%
- Relative humidity Storage 5 to 95%
- Installation elevation above sea level Maximum 2000 m
- Temperature Transport -25 to 70°C
- Relative humidity Transport Max. 95% at 40°C
- Temperature Storage -25 to 55°C
- Installation elevation above sea level Nominal 0 to 500 m
- Permissible mounting orientations Standing horizontally No
- Switching delay Enable 0 → 1, ready for PWM Max. 100 µs
- Energy efficiency (IE classification) Nominal losses in standby mode 13.2 W
- Energy efficiency (IE classification) Efficiency data IE2 (10,25) 3.5% ; IE2 (50,25) 3.5% ; IE2 (10,50) 3.6% ; IE2 (50,50) 3.7% ; IE2 (90,50) 3.8% ; IE2 (10,100) 4% ; IE2 (50,100) 4.2% ; IE2 (90,100) 4.5%
- Permissible mounting orientations Hanging vertically Yes
- Permissible mounting orientations Horizontal, face up Yes
- Switching delay Enable 1 → 0, PWM off Max. 2.0 ms
- Switching threshold High >15 V
- Switching delay Falling edge 53 µs ±0.5 µs (digitally filtered)
- Protective measures Short-circuit and ground fault protection Yes
- Switching delay Rising edge 52 µs ±0.5 µs (digitally filtered)
- Integrated line filter per EN 61800-3, category C3 Yes
- Switching threshold Low <5 V
- Input voltage Nominal 24 VDC
- Input voltage Maximum 30 VDC
- Electrical isolation Input - Input No
- Certifications UL cULus E225616; Power conversion equipment
- Protective measures Overload protection Yes
- Switch-on interval >10 s
- Reduction of continuous current depending on installation elevation Starting at 500 m above sea level 0.22 Aeff per 1000 m
- Frequency 50 / 60 Hz ±4%
- Certifications EAC Yes
- Certifications Functional safety Yes
- Certifications KC Yes
- Inrush current at 400 VAC 4 A
- Electrical isolation Input - ACOPOS Yes
- Mains input voltage 3x 400 VAC to 480 VAC ±10% ; 3x 230 VAC ±10%
- B&R ID code 0x1284
- Installed load Max. 3 kVA
- Certifications CE Yes
- Degree of protection per EN 60529 IP20
- Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
- Overvoltage category per EN 61800-5-1 II
- Discharge capacitance 660 nF
- OSSD signal connections Not permitted
- Modulation compared to ground potential Max. ±38 V
- Switching delay Max. 2.0 ms
- Input current at nominal voltage Approx. 4 mA
- Circuit Sink
- Continuous power 130 W
- Max. number of switching cycles Unlimited since implemented electronically
- Peak power output 3.5 kW
- Max. output current 1 A
- Response threshold for open-circuit monitoring Approx. 385 mA
- Max. output frequency 598 Hz
- Permissible network configurations TT, TN
- Max. motor line length 25 m
- Nominal switching frequency 20 kHz
- Possible switching frequencies 5 / 10 / 20 kHz
- Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
- Slots for plug-in modules 4
- Peak current 14 Aeff
- Continuous current 2.2 Aeff
- Input voltage 24 VDC ±25%
- DC bus capacitance 235 µF
- Input capacitance 8200 µF
- Current consumption Max. 2.5 A + Current for motor holding brake
- Quantity 1
- Power dissipation at device nominal power without braking resistor Approx. 120 W
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨