8V1016.501-2 B&R Electronic Components
Part#:8V1016.501-2
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
ACOPOS servo drive, 3x 110-230 V / 1x 110-230 V, 3.6 A, 0.7 kW, coated, integrated line filter, braking resistor and electronic safe restart interlock
Check out the 8V1016.501-2 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight2.5 kg
- Temperature Operation Nominal 5 to 40°C
- Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves 0.25 to 4 mm²
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 5 kHz No reduction
- Relative humidity Operation 5 to 85%
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 10 kHz No reduction
- Installation elevation above sea level Nominal 0 to 500 m
- Switching delay Rising edge 52 µs ±0.5 µs (digitally filtered)
- Electrical isolation Input - Input No
- Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
- Frequency 50 / 60 Hz ±4%
- Response threshold for open-circuit monitoring Approx. 245 mA
- Temperature Operation Maximum 55°C
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 10 kHz No reduction
- Terminal connection cross section Approbation data UL/C-UL-US 30 to 10 AWG
- Terminal connection cross section Approbation data CSA 28 to 10 AWG
- Reduction of continuous current depending on ambient temperature Mains input voltage: 230 VAC Switching frequency 20 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 20 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 110 VAC Switching frequency 5 kHz No reduction
- Dimensions Height 257 mm
- Dimensions Width 58.5 mm
- Dimensions Depth 220 mm
- Relative humidity Transport Max. 95% at 40°C
- Temperature Storage -25 to 55°C
- Relative humidity Storage 5 to 95%
- Installation elevation above sea level Maximum 2000 m
- Temperature Transport -25 to 70°C
- Permissible mounting orientations Standing horizontally No
- Switching delay Enable 1 → 0, PWM off Max. 2.0 ms
- Permissible mounting orientations Horizontal, face up Yes
- Energy efficiency (IE classification) Nominal losses in standby mode 12.5 W
- Switching delay Falling edge 53 µs ±0.5 µs (digitally filtered)
- Permissible mounting orientations Hanging vertically Yes
- Energy efficiency (IE classification) Efficiency data IE2 (10,25) 5.3% ; IE2 (50,25) 5.9% ; IE2 (10,50) 5.4% ; IE2 (50,50) 6.7% ; IE2 (90,50) 9% ; IE2 (10,100) 6.3% ; IE2 (50,100) 9.7% ; IE2 (90,100) 16.5%
- Switching delay Enable 0 → 1, ready for PWM Max. 100 µs
- Switching threshold High >15 V
- Switching threshold Low <5 V
- Input voltage Maximum 30 VDC
- Input voltage Nominal 24 VDC
- Protective measures Short-circuit and ground fault protection Yes
- Reduction of continuous current depending on installation elevation Starting at 500 m above sea level 0.36 Aeff per 1000 m
- Electrical isolation Input - ACOPOS Yes
- Protective measures Overload protection Yes
- Certifications KC Yes
- Certifications EAC Yes
- Certifications UL cULus E225616; Power conversion equipment
- Overvoltage category per EN 61800-5-1 II
- Certifications Functional safety Yes
- Certifications CE Yes
- Degree of protection per EN 60529 IP20
- OSSD signal connections Not permitted
- Modulation compared to ground potential Max. ±38 V
- Input current at nominal voltage Approx. 4 mA
- Circuit Sink
- Switching delay Max. 2.0 ms
- Peak power output 1.9 kW
- Max. output current 1.3 A
- Max. number of switching cycles Unlimited since implemented electronically
- Max. output frequency 598 Hz
- Continuous power 130 W
- Nominal switching frequency 10 kHz
- Possible switching frequencies 5 / 10 / 20 kHz
- Max. motor line length 15 m
- Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
- Peak current 12 Aeff
- Continuous current 3.6 Aeff
- Input capacitance 5600 µF
- Quantity 1
- DC bus capacitance 2040 µF
- Current consumption Max. 1.47 A + Current for motor holding brake
- Input voltage 24 VDC +25% / -20%
- Power dissipation at device nominal power without braking resistor 110 W
- Integrated line filter per EN 61800-3, category C3 Yes
- Note Variant with partially coated printed circuit boards
- B&R ID code 0xA6D7
- Mains input voltage 3x 110 VAC to 230 VAC ±10% or 1x 110 VAC to 230 VAC ±10%
- Installed load Max. 2.1 kVA
- Inrush current 5 A (at 230 VAC)
- Switch-on interval >10 s
- Permissible network configurations TT, TN
- Slots for plug-in modules 3
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨