8V1010.00-2 B&R Electronic Components
Part#:8V1010.00-2
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
ACOPOS servo drive, 3x 400-480 V, 1.0 A, 0.45 kW, integrated line filter, braking resistor and electronic safe restart interlock
Check out the 8V1010.00-2 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight2.5 kg
- Temperature Operation Maximum 55°C
- Temperature Operation Nominal 5 to 40°C
- Terminal connection cross section Approbation data CSA 28 to 10 AWG
- Terminal connection cross section Approbation data UL/C-UL-US 30 to 10 AWG
- Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves 0.25 to 4 mm²
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 20 kHz 0.13 Aeff per °C (starting at 45°C)
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 5 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 20 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 5 kHz No reduction
- Dimensions Depth 220 mm
- Relative humidity Transport Max. 95% at 40°C
- Dimensions Width 58.5 mm
- Relative humidity Storage 5 to 95%
- Dimensions Height 257 mm
- Relative humidity Operation 5 to 85%
- Temperature Transport -25 to 70°C
- Installation elevation above sea level Maximum 2000 m
- Permissible mounting orientations Standing horizontally No
- Installation elevation above sea level Nominal 0 to 500 m
- Temperature Storage -25 to 55°C
- Energy efficiency (IE classification) Nominal losses in standby mode 12.5 W
- Permissible mounting orientations Hanging vertically Yes
- Permissible mounting orientations Horizontal, face up Yes
- Switching delay Falling edge 53 µs ±0.5 µs (digitally filtered)
- Switching delay Enable 0 → 1, ready for PWM Max. 100 µs
- Switching delay Enable 1 → 0, PWM off Max. 2.0 ms
- Energy efficiency (IE classification) Efficiency data IE2 (10,25) 6.6% ; IE2 (50,25) 6.7% ; IE2 (10,50) 6.6% ; IE2 (50,50) 6.7% ; IE2 (90,50) 6.8% ; IE2 (10,100) 6.9% ; IE2 (50,100) 7% ; IE2 (90,100) 7.3%
- Switching delay Rising edge 52 µs ±0.5 µs (digitally filtered)
- Switching threshold High >15 V
- Switching threshold Low <5 V
- Input voltage Maximum 30 VDC
- Input voltage Nominal 24 VDC
- Electrical isolation Input - Input No
- Protective measures Short-circuit and ground fault protection Yes
- Electrical isolation Input - ACOPOS Yes
- Inrush current 2 A (at 400 VAC)
- Reduction of continuous current depending on installation elevation Starting at 500 m above sea level 0.1 Aeff per 1000 m
- Protective measures Overload protection Yes
- Certifications Functional safety Yes
- Certifications KC Yes
- Certifications CE Yes
- Degree of protection per EN 60529 IP20
- Certifications EAC Yes
- Certifications UL cULus E225616; Power conversion equipment
- Overvoltage category per EN 61800-5-1 II
- Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
- Switch-on interval >10 s
- Frequency 50 / 60 Hz ±4%
- Discharge capacitance 550 nF
- Slots for plug-in modules 3
- Integrated line filter per EN 61800-3, category C3 Yes
- Permissible network configurations TT, TN
- OSSD signal connections Not permitted
- Mains input voltage 3x 400 VAC to 480 VAC ±10%; 3x 230 VAC ±10%
- Switching delay Max. 2.0 ms
- Modulation compared to ground potential Max. ±38 V
- Input current at nominal voltage Approx. 4 mA
- Circuit Sink
- Continuous power 130 W
- Max. number of switching cycles Unlimited since implemented electronically
- Installed load Max. 1.35 kVA
- Max. output current 1.3 A
- Peak power output 2 kW
- Response threshold for open-circuit monitoring Approx. 245 mA
- Max. output frequency 598 Hz
- Max. motor line length 15 m
- Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
- Nominal switching frequency 10 kHz
- Possible switching frequencies 5 / 10 / 20 kHz
- Peak current 2.8 Aeff
- Input capacitance 5600 µF
- Continuous current 1 Aeff
- Current consumption Max. 1.47 A + Current for motor holding brake
- Quantity 1
- B&R ID code 0x18D6
- Input voltage 24 VDC +25% / -20%
- DC bus capacitance 165 µF
- Power dissipation at device nominal power without braking resistor 80 W
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨