8V1022.001-2 B&R Electronic Components
Part#:8V1022.001-2
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
ACOPOS servo drive, 3x 400-480 V, 2.2 A, 1 kW, coated, integrated line filter, braking resistor and electronic safe restart interlock
Check out the 8V1022.001-2 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight4 kg
- Temperature Operation Nominal 5 to 40°C
- Temperature Operation Maximum 55°C
- Terminal connection cross section Approbation data CSA 28 to 10 AWG
- Terminal connection cross section Flexible and fine-stranded wires With wire end sleeves 0.25 to 4 mm²
- Terminal connection cross section Approbation data UL/C-UL-US 30 to 10 AWG
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 20 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 20 kHz 0.13 Aeff per °C (starting at 51°C)
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 10 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 480 VAC Switching frequency 5 kHz No reduction
- Reduction of continuous current depending on ambient temperature Mains input voltage: 400 VAC Switching frequency 5 kHz No reduction
- Dimensions Depth 235.5 mm
- Relative humidity Transport Max. 95% at 40°C
- Dimensions Width 70.5 mm
- Dimensions Height 375 mm
- Relative humidity Operation 5 to 85%
- Temperature Transport -25 to 70°C
- Temperature Storage -25 to 55°C
- Relative humidity Storage 5 to 95%
- Installation elevation above sea level Maximum 2000 m
- Permissible mounting orientations Standing horizontally No
- Installation elevation above sea level Nominal 0 to 500 m
- Permissible mounting orientations Horizontal, face up Yes
- Permissible mounting orientations Hanging vertically Yes
- Energy efficiency (IE classification) Efficiency data IE2 (10,25) 3.5% ; IE2 (50,25) 3.5% ; IE2 (10,50) 3.6% ; IE2 (50,50) 3.7% ; IE2 (90,50) 3.8% ; IE2 (10,100) 4% ; IE2 (50,100) 4.2% ; IE2 (90,100) 4.5%
- Switching delay Falling edge 53 µs ±0.5 µs (digitally filtered)
- Energy efficiency (IE classification) Nominal losses in standby mode 13.2 W
- Switching delay Enable 0 → 1, ready for PWM Max. 100 µs
- Switching delay Enable 1 → 0, PWM off Max. 2.0 ms
- Switching threshold Low <5 V
- Switching delay Rising edge 52 µs ±0.5 µs (digitally filtered)
- Switching threshold High >15 V
- Input voltage Nominal 24 VDC
- Protective measures Overload protection Yes
- Protective measures Short-circuit and ground fault protection Yes
- Certifications KC Yes
- Electrical isolation Input - ACOPOS Yes
- Input voltage Maximum 30 VDC
- Electrical isolation Input - Input No
- Certifications Functional safety Yes
- Certifications EAC Yes
- Reduction of continuous current depending on installation elevation Starting at 500 m above sea level 0.22 Aeff per 1000 m
- Certifications UL cULus E225616; Power conversion equipment
- Certifications CE Yes
- Overvoltage category per EN 61800-5-1 II
- Pollution degree per EN 61800-5-1 2 (non-conductive pollution)
- Discharge capacitance 660 nF
- Degree of protection per EN 60529 IP20
- OSSD signal connections Not permitted
- Input current at nominal voltage Approx. 4 mA
- Modulation compared to ground potential Max. ±38 V
- Continuous power 130 W
- Switching delay Max. 2.0 ms
- Circuit Sink
- Peak power output 3.5 kW
- Max. number of switching cycles Unlimited since implemented electronically
- Max. output frequency 598 Hz
- Max. output current 1 A
- Possible switching frequencies 5 / 10 / 20 kHz
- Response threshold for open-circuit monitoring Approx. 385 mA
- Insulation stress of the connected motor per IEC TS 60034-25:2004 Limit value curve A
- Max. motor line length 25 m
- Peak current 14 Aeff
- Quantity 1
- Nominal switching frequency 20 kHz
- Input voltage 24 VDC ±25%
- Input capacitance 8200 µF
- DC bus capacitance 235 µF
- Continuous current 2.2 Aeff
- Current consumption Max. 2.5 A + Current for motor holding brake
- Power dissipation at device nominal power without braking resistor Approx. 120 W
- Integrated line filter per EN 61800-3, category C3 Yes
- B&R ID code 0xA099
- Installed load Max. 3 kVA
- Frequency 50 / 60 Hz ±4%
- Permissible network configurations TT, TN
- Slots for plug-in modules 4
- Inrush current at 400 VAC 4 A
- Note Variant with partially coated printed circuit boards
- Switch-on interval >10 s
- Mains input voltage 3x 400 VAC to 480 VAC ±10% ; 3x 230 VAC ±10%
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨