2904626 Phoenix Contact AC/DC Power Supplies

Product Details

• Mains variation/undervoltage
  SEMI F47-0706, EN 61000-4-11
• CSA
  CAN/CSA-C22.2 No. 60950-1-07
• Low Voltage Directive
  Conformance with Low Voltage Directive 2014/35/EC
• Contact discharge
  8 kV (Test Level 4)
• Test field strength
  1000 A/m
• Signal
  4 kV (Test Level 4 - asymmetrical)
• I/O/S
  asymmetrical
• Asymmetrical conducted disturbance variables
  EN 61000-4-16
• Input, output (test level 2)
  10 MHz
• Installation distance top/bottom
  50 mm / 50 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Derating
  > 60 °C (2.5%/K)
• Control deviation
  < 0.5 % (Static load change 10 % ... 90 %)
• MTBF (IEC 61709, SN 29500)
  > 1100000 h (25 °C)
• Mounting position
  horizontal DIN rail NS 35, EN 60715
• Conductor cross section AWG min.
  24
• Surge voltage load (surge)
  EN 61000-4-5
• Voltage dips
  EN 61000-4-11
• Test level 2
  150 Hz 1.5 kHz (Test Level 3)
• Input, output (test level 1)
  1 MHz (Test Level 3 - symmetrical)
Input, output (test level 3)
1 MHz (Test Level 3 - asymmetrical)
Efficiency
typ. 94 % (120 V AC)
Standard – Safety extra-low voltage
IEC 61010-1 (SELV)
SIQ
BG (type approved)
Flicker
EN 61000-3-3
Input
2 kV (Test Level 4 - symmetrical)
Pulse-shape magnetic field
EN 61000-4-9
Test level 3
1.5 kHz 15 kHz (Test Level 3)
Attenuated oscillating wave
EN 61000-4-18
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
Dielectric strength maximum
300 V AC 60 s
Current consumption
6.8 A (100 V AC)
Recommended breaker for input protection
10 A ... 16 A (Characteristic B, C, D, K or comparable)
Static Boost (IStat.Boost)
12.5 A
Height
130 mm
Connection in parallel
Yes, for redundancy and increased capacity
Protection against overvoltage at the output (OVP)
≤ 60 V DC
Conductor cross section flexible max.
1.5 mm²
EMC requirements, power plant
IEC 61850-3
Frequency range
50 Hz ... 60 Hz
Criterion A
Normal operating behavior within the specified limits.
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Nominal input voltage range
100 V AC ... 240 V AC
Typical response time
300 ms (from SLEEP MODE)
Insulation voltage input / PE
3.5 kV AC (type test)
HART FSK Physical Layer Test Specification Compliance
Output voltage UOut compliant
UL approvals
UL Listed UL 508
Comments
Criterion B
Conducted interference
EN 61000-4-6
Frequency
50 Hz
Test level 1
15 Hz 150 Hz (Test Level 3)
ECLASS 11.0
27040701
Height with alternative assembly
130 mm
Inrush current
typ. 11 A (at 25 °C)
Protective circuit/component
Varistor, gas-filled surge arrester
Net weight
1.3 kg
Width
70 mm
Degree of protection
IP20
Max. permissible relative humidity (operation)
≤ 100 % (at 25 °C, non-condensing)
Installation height
≤ 5000 m (> 2000 m, observe derating)
AC frequency range
50 Hz ... 60 Hz -10 % ... +10 %
Mains buffering time
typ. 32 ms (120 V AC)
Nominal output voltage
48 V DC
Nominal output current (IN)
10 A
Feedback voltage resistance
≤ 60 V DC
Maximum power dissipation in no-load condition
< 5 W (120 V AC)
Insulation voltage input/output
4 kV AC (type test)
Protection class
I
Conductor cross section solid max.
1 mm²
Conductor cross section AWG max.
16
Standard - Safety of transformers
IEC 61558-2-16 pending
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Shipbuilding approval
DNV GL, PRS, BV, LR, ABS
Conducted noise emission
EN 55016
Additional text
Test Level 2
Discharge in air
15 kV (Test Level 4)
Depth
125 mm
Depth with alternative assembly
73 mm
Inflammability class in acc. with UL 94 (housing / terminal blocks)
V0
Climatic class
3K3 (in acc. with EN 60721)
Frequency range (fN)
50 Hz ... 60 Hz -10 % ... +10 %
Type of protection
Transient surge protection
Dynamic Boost (IDyn.Boost)
15 A (5 s)
Residual ripple
< 70 mVPP (with nominal values)
Power loss nominal load max.
< 36 W (120 V AC)
Insulation voltage output / PE
0.5 kV DC (type test)
Connection method
Push-in connection
Assembly instructions
alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
EMC requirements for noise immunity
EN 61000-6-1
Standard - Electrical safety
IEC 61010-2-201 (SELV)
Standard - safety for equipment for measurement, control, and laboratory use
IEC 61010-1
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Harmonic currents
EN 61000-3-2
DNV GL noise radiation
Class B
Electromagnetic HF field
EN 61000-4-3
Width with alternative assembly
122 mm
Installation distance right/left
5 mm / 5 mm
Ambient temperature (start-up type tested)
-40 °C
Degree of pollution
2
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Nominal power consumption
519 VA
Discharge current to PE
< 3.5 mA
Input fuse
12 A (slow-blow, internal)
Setting range of the output voltage (USet)
48 V DC ... 56 V DC (constant capacity)
Selective Fuse Breaking (ISFB)
60 A (15 ms)
Connection in series
yes
Output power
480 W
Environmental protection directive
RoHS Directive 2011/65/EU
Conductor cross section solid min.
0.2 mm²
Stripping length
8 mm
Conductor cross section flexible min.
0.2 mm²
Standard - Safe isolation
IEC 61010-2-201
Rail applications
EN 50121-3-2
Noise emission
EN 55016
DNV GL conducted interference
Class A
Electrostatic discharge
EN 61000-4-2
Fast transients (burst)
EN 61000-4-4
Voltage
2.5 kV
Number of periods
0,5 / 1 / 5 / 50 / 250 periods
Attenuated sinusoidal oscillations (ring wave)
EN 61000-4-12
Test level 6
50 Hz 60 Hz (Test Level 3)
Criterion C
Temporary adverse effects on the operating behavior, which the device corrects automatically or which can be restored by actuating the operating elements.
Output
1 kV (Test Level 3 - symmetrical)
Power frequency magnetic field
EN 61000-4-8
Voltage dip
0 %
Test level 5
50 Hz 60 Hz (Test Level 3)
Test level 4
15 kHz 150 kHz (Test Level 3)
ECLASS 9.0
27040701
ECLASS 10.0.1
27040701