1162150 Phoenix Contact Electrical Wires & Cables

Product Details

• Type
  Locking actuator right
• Charging standard
  CCS type 2
• Width
  108 mm
• Max. altitude
  4000 m (above sea level)
• Number of power contacts
  5 (L1, N, PE, DC+, DC-)
• Rated current for signal contacts
  2 A
• Rated voltage for signal contacts
  30 V AC
• Standards/regulations
  DIN EN 60751
• Ambient temperature (operation)
  -40 °C ... 80 °C
• Conductor length
  2 m (AC cables)
• Rated current of power contacts
  32 A AC
• Resistor coding
  4.7 kΩ (between PE and PP)
• Insertion force
  < 100 N
• Required mounting screws
  M6
• Housing color
  black
• External sheath, color
  Green-yellow
• Outer sheath, material
  PVC
• Reverse current of the motor
  max. 1.5 A
• Cable length
  1 m
• Tolerance at the sensor with the recommended measured current
  ±5K
ECLASS 11.0
27144706
Application
For charging with alternating current (AC) and with direct current (DC)
Note
A protective cap is supplied as standard for the DC and AC contacts.
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Height
140.25 mm
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of phases
1
Number of signal contacts
2 (CP, PP)
Insulation resistance of neighboring contacts
> 200 MΩ
Temperature monitoring
AC contacts: PTC chain (DIN˽EN˽60738-1)
Withdrawal force
< 100 N
Material
Plastic
Locking type
Locking in the inserted state with a locking mechanism
Cable resistance
≤ 37.1 Ω/km
Single wire, color
black PP/CS
Number of positions of theconnectors
4
Recommended adaptation time
600 ms
Type of sensor
Pt 1000
Temperature range
-40 °C ... 130 °C
Charging mode
Mode 2, 3, 4
Depth
128.4 mm
Type of charging current
DC, AC 1-phase
Rated voltage for power contacts
250 V AC
Insertion/withdrawal cycles
> 10000
Mounting hole diameter
6.80 mm (ø)
Screws included in the scope of delivery
none
Design line
Generation 4
Material surface of contacts
Ag
Operating voltage
12 V (Typical power supply at the motor)
Max. dwell time with reverse current
1 s
Pause time after entry or exit path
3 s
ECLASS 10.0.1
27144706
Design
Generation 4
Note on the connection method
Crimp connection, cannot be disconnected
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Maximum charging power
200 kW
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Cable structure
4 x 0.5 mm²
Minimum bending radius
15 mm
Possible power supply range at the motor
9 V ... 16 V
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 9.0
27144706
Mounting position of the locking actuator
Right-side
Customer variations
On request
Flammability rating
V0
External cable diameter
1.6 mm -0.2 mm
Cable weight
7 kg/km
Maximum voltage for locking detection
12 V
Typical motor current for locking
0.25 A
Lock recognition
available
Mechanical emergency release
available
Resistance range
650 Ω ... 1450 Ω