1162148 Phoenix Contact Electrical Wires & Cables

1162148 Product Details

• Outer sheath, material
  PVC
• Type
  Locking actuator right
• Note
  A protective cap is supplied as standard for the DC and AC contacts.
• Ambient temperature (operation)
  -40 °C ... 80 °C
• Type of charging current
  DC, AC 1-phase
• Number of power contacts
  5 (L1, N, PE, DC+, DC-)
• Temperature measurement
  DC contacts: 2x PT1000 (DIN EN 60751)
• Insertion/withdrawal cycles
  > 10000
• Customer variations
  On request
• Cable resistance
  ≤ 37.1 Ω/km
• Possible power supply range at the motor
  9 V ... 16 V
• Reverse current of the motor
  max. 1.5 A
• Cable length
  1 m
• Tolerance at the sensor with the recommended measured current
  ±5K
• Charging mode
  Mode 2, 3, 4
• Width
  108 mm
• Bore dimensions
  117.65 mm x 90 mm, 117.65 mm x 83 mm
• Maximum charging power
  250 kW
• Rated current of power contacts
  32 A AC
• Type of signal transmission
  Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Insertion force
< 100 N
Mounting position of the locking actuator
Right-side
Mounting hole diameter
6.80 mm (ø)
Material
Plastic
Cable structure
4 x 0.5 mm²
External sheath, color
Green-yellow
Application
For charging with alternating current (AC) and with direct current (DC)
Note on the connection method
Crimp connection, cannot be disconnected
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of signal contacts
2 (CP, PP)
Insulation resistance of neighboring contacts
> 200 MΩ
Temperature monitoring
AC contacts: PTC chain (DIN˽EN˽60738-1)
Required mounting screws
M6
Flammability rating
V0
Locking type
Locking in the inserted state with a locking mechanism
Minimum bending radius
15 mm
Operating voltage
12 V (Typical power supply at the motor)
Typical motor current for locking
0.25 A
Mechanical emergency release
available
Resistance range
650 Ω ... 1450 Ω
Standards/regulations
DIN EN 60751
Depth
128.4 mm
Conductor length
2 m (AC cables)
Rated voltage for power contacts
250 V AC
Rated voltage for signal contacts
30 V AC
Withdrawal force
< 100 N
Design line
Generation 4
External cable diameter
1.6 mm -0.2 mm
Single wire, color
black PP/CS
Max. dwell time with reverse current
1 s
Service life insertion cycles
> 10000 load cycles
ECLASS 10.0.1
27144706
Design
Generation 4
Charging standard
CCS type 2
Height
140.25 mm
Max. altitude
4000 m (above sea level)
Number of phases
1
Rated current for signal contacts
2 A
Resistor coding
4.7 kΩ (between PE and PP)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Screws included in the scope of delivery
none
Housing color
black
Material surface of contacts
Ag
Cable weight
7 kg/km
Number of positions of theconnectors
4
Pause time after entry or exit path
3 s
Type of sensor
Pt 1000
Temperature range
-40 °C ... 130 °C
ECLASS 9.0
27144706
Maximum voltage for locking detection
12 V
Recommended adaptation time
600 ms
Lock recognition
available
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 11.0
27144706

Product condition