1162178 Phoenix Contact Electrical Wires & Cables

1162178 Product Details

• Standards/regulations
  DIN EN 60751
• Height
  151.2 mm
• Max. altitude
  4000 m (above sea level)
• Number of phases
  1
• Rated current for signal contacts
  2 A
• Temperature monitoring
  AC contacts: PTC chain (DIN˽EN˽60738-1)
• Insertion force
  < 100 N
• Required mounting screws
  M6
• Housing color
  black
• Flammability rating
  V0
• External sheath, color
  Green-yellow
• Single wire, color
  black PP/CS
• Max. dwell time with reverse current
  1 s
• Lock recognition
  available
• Mechanical emergency release
  available
• Temperature range
  -40 °C ... 130 °C
• Type
  Locking actuator top
• Charging standard
  CCS type 1
• Bore dimensions
  117.6 mm x 90 mm, 117.6 mm x 83 mm
• Maximum charging power
  200 kW
Number of power contacts
5 (L1, N, PE, DC+, DC-)
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Mounting position of the locking actuator
Top center
Customer variations
On request
Locking type
Locking in the inserted state with a locking mechanism
Minimum bending radius
15 mm
Possible power supply range at the motor
9 V ... 16 V
Recommended adaptation time
600 ms
Cable length
1 m
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
ECLASS 9.0
27144706
Design
Generation 4
Note on the connection method
Crimp connection, cannot be disconnected
Width
108 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of signal contacts
2 (CP, CS)
Insulation resistance of neighboring contacts
> 200 MΩ
Insertion/withdrawal cycles
> 10000
Screws included in the scope of delivery
none
Cable structure
4 x 0.5 mm²
Cable resistance
≤ 37.1 Ω/km
Outer sheath, material
PVC
Operating voltage
12 V (Typical power supply at the motor)
Pause time after entry or exit path
3 s
Tolerance at the sensor with the recommended measured current
±5K
ECLASS 11.0
27144706
Note
A protective cap is supplied as standard for the DC and AC contacts.
Conductor length
2 m (AC cables)
Rated voltage for power contacts
250 V AC
Rated voltage for signal contacts
30 V AC
Withdrawal force
< 100 N
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Design line
Generation 4
Material surface of contacts
Ag
Number of positions of theconnectors
4
Maximum voltage for locking detection
12 V
Service life insertion cycles
> 10000 load cycles
Resistance range
650 Ω ... 1450 Ω
Application
For charging with alternating current (AC) and with direct current (DC)
Charging mode
Mode 2, 3, 4
Depth
122.8 mm
Ambient temperature (operation)
-40 °C ... 80 °C
Type of charging current
DC, AC 1-phase
Rated current of power contacts
48 A AC
Resistor coding
2.7 kΩ (between PE and CS)
Mounting hole diameter
6.80 mm (ø)
Material
Plastic
External cable diameter
1.6 mm -0.2 mm
Cable weight
7 kg/km
Typical motor current for locking
0.25 A
Reverse current of the motor
max. 1.5 A
Type of sensor
Pt 1000
ECLASS 10.0.1
27144706

Product condition