1162163 Phoenix Contact Electrical Wires & Cables

1162163 Product Details

• Application
  For charging with alternating current (AC) and with direct current (DC)
• Height
  151.2 mm
• Conductor length
  2 m (AC cables)
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Max. altitude
  4000 m (above sea level)
• Number of power contacts
  5 (L1, N, PE, DC+, DC-)
• Type
  Locking actuator top
• Note
  A protective cap is supplied as standard for the DC and AC contacts.
• Ambient temperature (operation)
  -40 °C ... 80 °C
• Maximum charging power
  250 kW
• Rated current of power contacts
  80 A AC
• Type of signal transmission
  Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
• Insertion/withdrawal cycles
  > 10000
• Required mounting screws
  M6
• Material
  Plastic
• External cable diameter
  1.6 mm -0.2 mm
• External sheath, color
  Green-yellow
• Cable weight
  7 kg/km
• Design
  Generation 4
• Standards/regulations
  DIN EN 60751
Width
108 mm
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of signal contacts
2 (CP, CS)
Rated voltage for signal contacts
30 V AC
Temperature monitoring
AC contacts: PTC chain (DIN˽EN˽60738-1)
Design line
Generation 4
Locking type
Locking in the inserted state with a locking mechanism
Minimum bending radius
15 mm
Typical motor current for locking
0.25 A
Lock recognition
available
Resistance range
650 Ω ... 1450 Ω
ECLASS 9.0
27144706
Charging standard
CCS type 1
Charging mode
Mode 2, 3, 4
Depth
122.8 mm
Number of phases
1
Rated current for signal contacts
2 A
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Customer variations
On request
Material surface of contacts
Ag
Number of positions of theconnectors
4
Reverse current of the motor
max. 1.5 A
Type of sensor
Pt 1000
ECLASS 11.0
27144706
Note on the connection method
Crimp connection, cannot be disconnected
Bore dimensions
117.6 mm x 90 mm, 117.6 mm x 83 mm
Type of charging current
DC, AC 1-phase
Rated voltage for power contacts
250 V AC
Insulation resistance of neighboring contacts
> 200 MΩ
Withdrawal force
< 100 N
Screws included in the scope of delivery
none
Housing color
black
Outer sheath, material
PVC
Single wire, color
black PP/CS
Possible power supply range at the motor
9 V ... 16 V
Pause time after entry or exit path
3 s
Mechanical emergency release
available
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Tolerance at the sensor with the recommended measured current
±5K
Resistor coding
2.7 kΩ (between PE and CS)
Insertion force
< 100 N
Mounting hole diameter
6.80 mm (ø)
Mounting position of the locking actuator
Top center
Flammability rating
V0
Cable structure
4 x 0.5 mm²
Cable resistance
≤ 37.1 Ω/km
Operating voltage
12 V (Typical power supply at the motor)
Maximum voltage for locking detection
12 V
Recommended adaptation time
600 ms
Temperature range
-40 °C ... 130 °C
Max. dwell time with reverse current
1 s
Service life insertion cycles
> 10000 load cycles
Cable length
1 m
ECLASS 10.0.1
27144706

Product condition