1162095 Phoenix Contact Electrical Wires & Cables

1162095 Product Details

• Design
  Generation 4
• Note
  A protective cap is supplied as standard for the DC and AC contacts.
• Conductor length
  2 m (AC cables)
• Number of phases
  3
• Insulation resistance of neighboring contacts
  > 200 MΩ
• Temperature monitoring
  AC contacts: PTC chain (DIN˽EN˽60738-1)
• Mounting position of the locking actuator
  Right-side
• Customer variations
  On request
• External cable diameter
  1.6 mm -0.2 mm
• Single wire, color
  black PP/CS
• Maximum voltage for locking detection
  12 V
• Pause time after entry or exit path
  3 s
• Type of sensor
  Pt 1000
• ECLASS 11.0
  27144706
• Type
  Locking actuator right
• Width
  108 mm
• Degree of protection
  IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
• Type of charging current
  DC, AC 3-phase
• Maximum charging power
  250 kW
• Rated current for signal contacts
  2 A
Temperature measurement
DC contacts: 2x PT1000 (DIN EN 60751)
Insertion/withdrawal cycles
> 10000
Design line
Generation 4
Material surface of contacts
Ag
Outer sheath, material
PVC
Minimum bending radius
15 mm
Operating voltage
12 V (Typical power supply at the motor)
Lock recognition
available
Temperature range
-40 °C ... 130 °C
ECLASS 10.0.1
27144706
Standards/regulations
DIN EN 60751
Height
140.25 mm
Depth
128.4 mm
Ambient temperature (operation)
-40 °C ... 80 °C
Rated current of power contacts
32 A AC
Resistor coding
4.7 kΩ (between PE and PP)
Restrictions to mounting position
Only 0 to 90 degree frontal inclination possible, see figure
Screws included in the scope of delivery
none
Material
Plastic
Locking type
Locking in the inserted state with a locking mechanism
Number of positions of theconnectors
4
Max. dwell time with reverse current
1 s
Typical motor current for locking
0.25 A
Mechanical emergency release
available
Resistance range
650 Ω ... 1450 Ω
Charging standard
CCS type 2
Bore dimensions
117.65 mm x 90 mm, 117.65 mm x 83 mm
Max. altitude
4000 m (above sea level)
Number of power contacts
7 (L1, L2, L3, N, PE, DC+, DC-)
Rated voltage for power contacts
480 V AC
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Withdrawal force
< 100 N
Housing color
black
Flammability rating
V0
Cable resistance
≤ 37.1 Ω/km
Cable weight
7 kg/km
Possible power supply range at the motor
9 V ... 16 V
Recommended adaptation time
600 ms
Service life insertion cycles
> 10000 load cycles
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Application
For charging with alternating current (AC) and with direct current (DC)
Charging mode
Mode 2, 3, 4
Note on the connection method
Crimp connection, cannot be disconnected
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Number of signal contacts
2 (CP, PP)
Rated voltage for signal contacts
30 V AC
Insertion force
< 100 N
Required mounting screws
M6
Mounting hole diameter
6.80 mm (ø)
Cable structure
4 x 0.5 mm²
External sheath, color
Green-yellow
Reverse current of the motor
max. 1.5 A
Cable length
1 m
Tolerance at the sensor with the recommended measured current
±5K
ECLASS 9.0
27144706

Product condition