3211819 Phoenix Contact Terminal Blocks

Product Details

• Permissible humidity (storage/transport)
  30 % ... 70 %
• UNSPSC 7.0901
  39121410
• ECLASS 11.0
  27141120
• ETIM 4.0
  EC000897
• ETIM 7.0
  EC000897
• UNSPSC 20.0
  39121410
• UNSPSC 6.01
  30211811
• UNSPSC 19.0
  39121410
• Conductor cross section flexible, with ferrule with plastic sleeve min.
  1 mm²
• Rated surge voltage
  8 kV
• Overvoltage category
  III
• Nominal cross section
  6 mm²
• Result of tight fit on support
  Test passed
• Tight fit on carrier
  NS 35
• Short-time current
  0.72 kA
• Test specification, oscillation, broadband noise
  DIN EN 50155 (VDE 0115-200):2008-03
• Test duration per axis
  5 h
• Shock duration
  18 ms
• Calorimetric heat release NFPA 130 (ASTM E 1354)
  27,5 MJ/kg
• Width
  8.2 mm
Height NS 35/15
51 mm
Potentials
1
Degree of pollution
3
Finger protection
guaranteed
Back of the hand protection
guaranteed
Result of temperature-rise test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Result of thermal test
Test passed
Oscillation, broadband noise test result
Test passed
Test directions
X-, Y- and Z-axis (pos. and neg.)
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Connection
1 level
Conductor cross section solid max.
10 mm²
Conductor cross section AWG min.
20
Conductor cross section flexible max.
10 mm²
Number of levels
1
Flammability rating according to UL 94
V0
Maximum power dissipation for nominal condition
1.31 W
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Power frequency withstand voltage setpoint
2.2 kV
Bending test turns
135
Tensile test result
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Number of shocks per direction
3
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Number of connections
2
Area of application
Railway industry
Insulating material group
I
Nominal current IN
41 A
Result of surge voltage test
Test passed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Setpoint
5 N
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Test spectrum
Service life test category 2, bogie-mounted
Color
blue
Insulating material
PA
Maximum load current
52 A (with 10 mm² conductor cross section, rigid)
Open side panel
Yes
Result of power-frequency withstand voltage test
Test passed
Result of flexion and pull-out test
Test passed
Tractive force setpoint
90 N
Result of voltage-drop test
Test passed
Short circuit stability result
Test passed
Result of aging test
Test passed
Connection cross sections directly pluggable
1 mm² 10 mm²
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 5.0
27141100
ECLASS 9.0
27141120
Acceleration
30g
Shock form
Half-sine
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Height
42.2 mm
Length
57.7 mm
Conductor cross section flexible min.
0.5 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
End cover width
2.2 mm
Connection in acc. with standard
CSA
Conductor cross section AWG max.
8
Conductor cross section flexible, with ferrule without plastic sleeve min.
1 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 10.0.1
27141120
ECLASS 4.1
27141100
ECLASS 7.0
27141120
UNSPSC 12.01
39121410
UNSPSC 21.0
39121410
Nominal voltage UN
1000 V
Surge voltage test setpoint
9.8 kV
Bending test rotation speed
10 rpm
Conductor cross section tensile test
10 mm²
Requirements, voltage drop
U1 ≤ 3.2 mV; U2 ≤ 1.5 x U1
Conductor cross section short circuit testing
6 mm²
Ageing test for screwless modular terminal block temperature cycles
192
ASD level
6.12 (m/s2)2/Hz
Shock test result
Test passed
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Surface flammability NFPA 130 (ASTM E 162)
passed
Min. AWG conductor cross section, flexible
20
Height NS 35/7,5
43.5 mm
Stripping length
10 mm ... 12 mm
Connection method
Push-in connection
Conductor cross section solid min.
1 mm²
Internal cylindrical gage
A5
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 4.0
27141100
ECLASS 5.1
27141100
ETIM 6.0
EC000897
UNSPSC 13.2
39121410
Max. AWG conductor cross section, flexible
10
ECLASS 6.0
27141100
UNSPSC 11
39121410
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
2.5 mm² When using TWIN ferrules, we recommend a minimum ferrule length of 13 mm.
UNSPSC 18.0
39121410