3076033 Phoenix Contact Terminal Blocks

Product Details

• Number of connections
  4
• Rated surge voltage
  4 kV
• Open side panel
  Yes
• Result of surge voltage test
  Test passed
• Bending test turns
  135
• Requirements, voltage drop
  ≤ 3.2 mV
• Test specification, oscillation, broadband noise
  DIN EN 50155 (VDE 0115-200):2008-03
• Test duration per axis
  5 h
• Surface flammability NFPA 130 (ASTM E 162)
  passed
• Calorimetric heat release NFPA 130 (ASTM E 1354)
  27,5 MJ/kg
• Fire protection for rail vehicles (DIN EN 45545-2) R23
  HL 1 - HL 3
• End cover width
  2.2 mm
• Conductor cross section solid min.
  0.2 mm²
• Conductor cross section flexible, with ferrule without plastic sleeve min.
  0.25 mm²
• Conductor cross section flexible, with ferrule with plastic sleeve min.
  0.25 mm²
• 2 conductors with same cross section, stranded max.
  1.5 mm²
• Screw thread
  M3
• Tightening torque, min
  0.5 Nm
• Color
  gray
• Degree of pollution
  3
Nominal voltage UN
400 V (phase conductor/phase conductor)
Maximum load current (upper level)
16 A (with 4 mm² conductor cross section)
Finger protection
guaranteed
Power frequency withstand voltage setpoint
1.89 kV
Result of flexion and pull-out test
Test passed
Tensile test result
Test passed
Result of tight fit on support
Test passed
Result of voltage-drop test
Test passed
Result of thermal test
Test passed
ASD level
6.12 (m/s2)2/Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Number of shocks per direction
3
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Length
93.5 mm
Height NS 35/15
59 mm
Conductor cross section flexible min.
0.2 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
2.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
0.75 mm²
2 conductors with same cross section, stranded min.
0.2 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 11.0
27141125
ECLASS 5.1
27141100
ETIM 4.0
EC001329
UNSPSC 11
39121410
UNSPSC 21.0
39121410
Nominal cross section
4 mm²
Flammability rating according to UL 94
V0
Overvoltage category
III
Nominal current IN
24 A (with 4 mm² conductor cross section)
Surge voltage test setpoint
7.3 kV
Bending test rotation speed
10 rpm
Tractive force setpoint
60 N
Setpoint
1 N
Short circuit stability result
Test passed
Short-time current
0.48 kA
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Shock form
Half-sine
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Width
5.2 mm
Conductor cross section flexible max.
4 mm²
2 conductors with same cross section, solid min.
0.2 mm²
Connection method
Screw connection
Internal cylindrical gage
A3
Tightening torque max
0.6 Nm
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 10.0.1
27141125
ECLASS 7.0
27141125
UNSPSC 6.01
30211811
UNSPSC 12.01
39121410
Number of levels
3
Maximum load current
30 A (with 4 mm² conductor cross section and 3-pos. terminal block)
Maximum power dissipation for nominal condition
1.02 W (the value is multiplied when connecting multiple levels)
Nominal current IN (upper level)
16 A (with 4 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Result of power-frequency withstand voltage test
Test passed
Bending test conductor cross section/weight
0.2 mm² / 0.2 kg
Tight fit on carrier
NS 35
Result of temperature-rise test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Acceleration
30g
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Note
Please observe the current carrying capacity of the DIN rails.
Conductor cross section solid max.
4 mm²
Conductor cross section AWG min.
24
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
0.75 mm²
2 conductors with same cross section, solid max.
1.5 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 125°C)
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.0
27141100
ECLASS 6.0
27141100
ETIM 7.0
EC001329
UNSPSC 18.0
39121410
UNSPSC 13.2
39121410
Insulating material
PA
Insulating material group
I
Back of the hand protection
guaranteed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Conductor cross section tensile test
4 mm²
Conductor cross section short circuit testing
4 mm²
Oscillation, broadband noise test result
Test passed
Test spectrum
Service life test category 2, bogie-mounted
Shock test result
Test passed
Shock duration
18 ms
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Height NS 35/7,5
51.5 mm
Conductor cross section AWG max.
12
Conductor cross section flexible, with ferrule with plastic sleeve max.
2.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.25 mm²
Stripping length
9 mm
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 4.0
27141100
ECLASS 9.0
27141125
ETIM 6.0
EC001329
UNSPSC 20.0
39121410
Connection in acc. with standard
CSA
ECLASS 4.1
27141100
ETIM 3.0
EC000897
UNSPSC 7.0901
39121410
UNSPSC 19.0
39121410