3064247 Phoenix Contact Terminal Blocks

Product Details

• Number of connections
  2
• Overvoltage category
  III
• Nominal current IN
  57 A
• Back of the hand protection
  guaranteed
• Result of the test for mechanical stability of terminal points (5 x conductor connection)
  Test passed
• Result of power-frequency withstand voltage test
  Test passed
• Setpoint
  5 N
• Requirement temperature-rise test
  Increase in temperature ≤ 45 K
• Ageing test for screwless modular terminal block temperature cycles
  192
• Test frequency
  f1 = 5 Hz to f2 = 250 Hz
• Test directions
  X-, Y- and Z-axis (pos. and neg.)
• Shock duration
  18 ms
• Specific optical density of smoke NFPA 130 (ASTM E 662)
  passed
• Static insulating material application in cold
  -60 °C
• Fire protection for rail vehicles (DIN EN 45545-2) R22
  HL 1 - HL 3
• Insulating material
  PA
• Degree of pollution
  3
• Open side panel
  Yes
• Result of surge voltage test
  Test passed
• Power frequency withstand voltage setpoint
  2.2 kV
Bending test turns
135
Result of voltage-drop test
Test passed
Result of temperature-rise test
Test passed
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2018-05
ASD level
6.12 (m/s2)2/Hz
Shock form
Half-sine
Number of shocks per direction
3
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Width
10.2 mm
Height NS 35/7,5
47.5 mm
Connection in acc. with standard
IEC 60947-7-1
Stripping length
10 mm
Conductor cross section solid max.
16 mm²
Conductor cross section flexible min.
0.5 mm²
Nominal cross section
10 mm²
Rated surge voltage
8 kV
Maximum power dissipation for nominal condition
1.82 W
Nominal voltage UN
1000 V
Surge voltage test setpoint
9.6 kV
Bending test rotation speed
10 rpm
Tight fit on carrier
NS 35
Requirements, voltage drop
U1 ≤ 3.2 mV; U2 ≤ 1.5 x U1
Proof of thermal characteristics (needle flame) effective duration
30 s
Test spectrum
Service life test category 2, bogie-mounted
Acceleration
30g
Test duration per axis
5 h
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Surface flammability NFPA 130 (ASTM E 162)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
End cover width
2.2 mm
Height NS 35/15
55 mm
Screw thread
M4
Tightening torque max
1.8 Nm
Conductor cross section solid min.
0.5 mm²
Conductor cross section AWG max.
6
Min. AWG conductor cross section, flexible
20
Conductor cross section flexible, with ferrule without plastic sleeve max.
10 mm²
2 conductors with same cross section, solid max.
4 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
6 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 4.0
27141100
Number of levels
1
Flammability rating according to UL 94
V0
Insulating material group
I
2 conductors with same cross section, stranded max.
4 mm²
Internal cylindrical gage
A6
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 4.1
27141100
ECLASS 9.0
27141120
UNSPSC 6.01
30211811
UNSPSC 13.2
39121410
Potentials
1
Color
gray
Maximum load current
76 A (with 16 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Finger protection
guaranteed
Result of flexion and pull-out test
Test passed
Tensile test result
Test passed
Result of tight fit on support
Test passed
Result of thermal test
Test passed
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 11.0
27141120
ECLASS 6.0
27141100
ETIM 4.0
EC000897
UNSPSC 11
39121410
UNSPSC 19.0
39121410
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Length
47.7 mm
Height
46.9 mm
Connection method
Screw connection
Tightening torque, min
1.5 Nm
Note
Note: Product releases, connection cross sections and notes on connecting aluminum cables can be found in the download area.
Conductor cross section AWG min.
20
Conductor cross section flexible max.
16 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
10 mm²
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
2 conductors with same cross section, stranded min.
0.5 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 10.0.1
27141120
ECLASS 7.0
27141120
ETIM 6.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 21.0
39121410
Max. AWG conductor cross section, flexible
6
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
2 conductors with same cross section, solid min.
0.5 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
2.5 mm²
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.0
27141100
ETIM 3.0
EC000897
UNSPSC 7.0901
39121410
UNSPSC 20.0
39121410
ECLASS 5.1
27141100
ETIM 7.0
EC000897
UNSPSC 18.0
39121410