3064085 Phoenix Contact Terminal Blocks

Product Details

• Potentials
  1
• Insulating material
  PA
• Overvoltage category
  III
• Open side panel
  Yes
• Result of flexion and pull-out test
  Test passed
• Result of tight fit on support
  Test passed
• Result of temperature-rise test
  Test passed
• Result of thermal test
  Test passed
• Test duration per axis
  5 h
• Number of shocks per direction
  3
• Static insulating material application in cold
  -60 °C
• Smoke gas toxicity NFPA 130 (SMP 800C)
  passed
• Fire protection for rail vehicles (DIN EN 45545-2) R26
  HL 1 - HL 3
• Length
  57.8 mm
• Screw thread
  M3
• Conductor cross section AWG min.
  26
• Number of positions
  1
• Nominal cross section
  2.5 mm²
• Flammability rating according to UL 94
  V0
• Nominal voltage UN
  800 V
Result of power-frequency withstand voltage test
Test passed
Tensile test result
Test passed
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Short-time current
0.3 kA
ASD level
0.02 g²/Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Tightening torque max
0.6 Nm
Tightening torque, min
0.5 Nm
Max. AWG conductor cross section, flexible
12
Conductor cross section flexible, with ferrule with plastic sleeve max.
2.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.14 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
Permissible humidity (storage/transport)
30 % ... 70 %
ETIM 3.0
EC000902
UNSPSC 6.01
30211811
UNSPSC 13.2
39121410
Color
gray
Maximum load current
32 A (with 4 mm² conductor cross section)
Finger protection
guaranteed
Power frequency withstand voltage setpoint
2 kV
Bending test conductor cross section/weight
0.14 mm² / 0.2 kg
Result of voltage-drop test
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Proof of thermal characteristics (needle flame) effective duration
30 s
Test spectrum
Service life test category 1, class B, body mounted
Shock form
Half-sine
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
End cover width
2.2 mm
Number of connections
2
Rated surge voltage
8 kV
Degree of pollution
3
Maximum power dissipation for nominal condition
0.77 W
Result of surge voltage test
Test passed
Bending test turns
135
Tractive force setpoint
60 N
Tight fit on carrier
NS 35
Conductor cross section short circuit testing
2.5 mm²
Acceleration
5g
Shock duration
30 ms
Surface flammability NFPA 130 (ASTM E 162)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Width
5.2 mm
Height NS 35/7,5
47.5 mm
Conductor cross section solid min.
0.14 mm²
Conductor cross section AWG max.
12
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.14 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 4.1
27141100
ECLASS 9.0
27141120
ETIM 6.0
EC000897
UNSPSC 18.0
39121410
UNSPSC 19.0
39121410
Number of levels
1
Insulating material group
I
Nominal current IN
24 A
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Back of the hand protection
guaranteed
Bending test rotation speed
10 rpm
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Conductor cross section tensile test
4 mm²
Requirements, voltage drop
U1 ≤ 3.2 mV; U2 ≤ 1.5 x U1
Short circuit stability result
Test passed
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Test frequency
f1 = 5 Hz to f2 = 150 Hz
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Height NS 35/15
55 mm
Stripping length
9 mm
Conductor cross section solid max.
4 mm²
Conductor cross section flexible max.
4 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.14 mm²
2 conductors with same cross section, stranded max.
1.5 mm²
Internal cylindrical gage
A3
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.0
27141100
ECLASS 5.1
27141100
ETIM 2.0
EC000902
UNSPSC 12.01
39121410
UNSPSC 20.0
39121410
Connection method
Screw connection
Connection in acc. with standard
CSA
Conductor cross section flexible min.
0.14 mm²
Min. AWG conductor cross section, flexible
26
2 conductors with same cross section, solid min.
0.14 mm²
2 conductors with same cross section, solid max.
1.5 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 10.0.1
27141120
ECLASS 4.0
27141100
ECLASS 7.0
27141126
ETIM 7.0
EC000897
UNSPSC 11
39121410
Conductor cross section flexible, with ferrule without plastic sleeve max.
2.5 mm²
2 conductors with same cross section, stranded min.
0.14 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
1.5 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 11.0
27141120
ECLASS 6.0
27141100
ETIM 4.0
EC000902
UNSPSC 7.0901
39121410
UNSPSC 21.0
39121410