3046146 Phoenix Contact Terminal Blocks

Product Details

• Insulating material
  PA
• Insulating material group
  I
• Back of the hand protection
  guaranteed
• Surge voltage test setpoint
  7.2 kV
• Result of the test for mechanical stability of terminal points (5 x conductor connection)
  Test passed
• Bending test rotation speed
  10 (+/- 2) rpm
• Tractive force setpoint
  80 N
• Tight fit on carrier
  NS 35
• Requirement temperature-rise test
  Increase in temperature ≤ 45 K
• Proof of thermal characteristics (needle flame) effective duration
  30 s
• Acceleration
  30g
• Finger protection
  guaranteed
• Number of connections
  2
• Flammability rating according to UL 94
  V0
• Area of application
  Machine building
• Maximum power dissipation for nominal condition
  1.02 W
• Nominal voltage UN
  500 V
• Shock protection test specification
  IEC 60529:2001-02
• Power frequency withstand voltage setpoint
  1.89 kV
• Conductor cross section tensile test
  6 mm²
Result of voltage-drop test
Test passed
Note
The max. load current must not be exceeded by the total current of all connected conductors.
Short-time current
0.3 kA
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2018-05
ASD level
6.12 (m/s2)2/Hz
Shock form
Semi-sinusoidal
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Surface flammability NFPA 130 (ASTM E 162)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Height NS 35/15
56.6 mm
Tightening torque, min
0.6 Nm
Conductor cross section solid max.
6 mm²
Min. AWG conductor cross section, flexible
26
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.14 mm²
Number of levels
1
Nominal cross section
4 mm²
Rated surge voltage
6 kV
Overvoltage category
III
Nominal current IN
20 A
Result of power-frequency withstand voltage test
Test passed
Bending test turns
135
Bending test conductor cross section/weight
0.14 mm² / 0.2 kg
Requirements, voltage drop
U1 ≤ 6,4 mV (1,6 mV x number of conductorclamping units or disconnect unit contactpoints)U2 ≤ 1,5 x U1
Conductor cross section short circuit testing
2.5 mm²
Test spectrum
Service life test category 2, bogie-mounted
Test directions
X-, Y- and Z-axis (pos. and neg.)
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Tightening torque max
0.8 Nm
Conductor cross section solid min.
0.14 mm²
Conductor cross section AWG max.
10
Conductor cross section flexible min.
0.14 mm²
2 conductors with same cross section, solid min.
0.14 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
1.5 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.0
27141100
ETIM 7.0
EC000902
UNSPSC 20.0
39121410
Potentials
1
Color
gray
Degree of pollution
3
Maximum load current
20 A (with 6 mm² conductor cross section)
Open side panel
No
Result of surge voltage test
Test passed
Result of flexion and pull-out test
Test passed
Tensile test result
Test passed
Result of tight fit on support
Test passed
Result of temperature-rise test
Test passed
Short circuit stability result
Test passed
Result of thermal test
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Test duration per axis
5 h
Shock duration
18 ms
Number of shocks per direction
3
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Width
6.2 mm
Connection method
Screw connection
Screw thread
M3
Connection in acc. with standard
IEC 60947-7-1
Max. AWG conductor cross section, flexible
10
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.14 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
4 mm²
2 conductors with same cross section, stranded min.
0.14 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 125°C)
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 5.1
27141100
ECLASS 9.0
27141126
UNSPSC 21.0
39121410
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Height NS 35/7,5
49.1 mm
Length
57.8 mm
Stripping length
9 mm
Conductor cross section AWG min.
26
Conductor cross section flexible max.
6 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
4 mm²
2 conductors with same cross section, stranded max.
1.5 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.14 mm²
Internal cylindrical gage
A4
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 10.0.1
27141126
ETIM 6.0
EC000902
UNSPSC 13.2
39121410
2 conductors with same cross section, solid max.
1.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
2.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 11.0
27141126
ECLASS 6.0
27141100
ECLASS 7.0
27141126
UNSPSC 19.0
39121410
UNSPSC 18.0
39121410