3046375 Phoenix Contact Terminal Blocks

Product Details

• Number of connections
  2
• Area of application
  Railway industry
• Maximum power dissipation for nominal condition
  0.77 W
• Nominal current IN
  20 A (with 4 mm² conductor cross section)
• Result of surge voltage test
  Test passed
• Bending test rotation speed
  10 (+/- 2) rpm
• Bending test conductor cross section/weight
  0.14 mm² / 0.2 kg
• Requirements, voltage drop
  U1 ≤ 6,4 mV (1,6 mV x number of conductorclamping units or disconnect unit contactpoints)U2 ≤ 1,5 x U1
• Requirement temperature-rise test
  Increase in temperature ≤ 45 K
• Proof of thermal characteristics (needle flame) effective duration
  30 s
• Test frequency
  f1 = 5 Hz to f2 = 250 Hz
• Insulating material
  PA
• Insulating material group
  I
• Finger protection
  guaranteed
• Surge voltage test setpoint
  7.3 kV
• Tensile test result
  Test passed
• Tractive force setpoint
  60 N
• Result of temperature-rise test
  Test passed
• Note
  The max. load current must not be exceeded by the total current of all connected conductors.
• Short-time current
  0.3 kA
Test directions
X-, Y- and Z-axis (pos. and neg.)
Shock duration
18 ms
Static insulating material application in cold
-60 °C
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Length
57.8 mm
Tightening torque max
0.6 Nm
Conductor cross section AWG min.
26
Min. AWG conductor cross section, flexible
26
Conductor cross section flexible, with ferrule with plastic sleeve max.
2.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Number of levels
1
Rated surge voltage
6 kV
Overvoltage category
III
Back of the hand protection
guaranteed
Result of power-frequency withstand voltage test
Test passed
Bending test turns
135
Result of tight fit on support
Test passed
Result of voltage-drop test
Test passed
Conductor cross section short circuit testing
2.5 mm²
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2018-05
Acceleration
30g
Shock form
Semi-sinusoidal
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
End cover width
2.2 mm
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Connection method
Screw connection
Tightening torque, min
0.5 Nm
Conductor cross section solid min.
0.14 mm²
Nominal cross section
2.5 mm²
Flammability rating according to UL 94
V0
Maximum load current
20 A (with 4 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Power frequency withstand voltage setpoint
1.89 kV
ETIM 3.0
EC000902
UNSPSC 6.01
30211811
Color
gray
Degree of pollution
3
Nominal voltage UN
400 V
Open side panel
Yes
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Result of flexion and pull-out test
Test passed
Conductor cross section tensile test
4 mm²
Tight fit on carrier
NS 35
Short circuit stability result
Test passed
Test spectrum
Service life test category 2, bogie-mounted
ASD level
6.12 (m/s2)2/Hz
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Surface flammability NFPA 130 (ASTM E 162)
passed
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Height NS 35/7,5
49.1 mm
Screw thread
M3
Conductor cross section solid max.
4 mm²
Conductor cross section AWG max.
12
Max. AWG conductor cross section, flexible
12
2 conductors with same cross section, solid max.
1.5 mm²
2 conductors with same cross section, stranded min.
0.14 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
1.5 mm²
Ambient temperature (actuation)
-5 °C ... 70 °C
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 4.0
27141100
ECLASS 6.0
27141100
ECLASS 7.0
27141126
UNSPSC 13.2
39121410
UNSPSC 20.0
39121410
Test duration per axis
5 h
Number of shocks per direction
3
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Width
5.2 mm
Height NS 35/15
56.6 mm
Stripping length
9 mm
Connection in acc. with standard
CSA
Conductor cross section flexible max.
4 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
2.5 mm²
2 conductors with same cross section, solid min.
0.14 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.14 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 125°C)
ECLASS 11.0
27141126
ECLASS 10.0.1
27141126
ECLASS 4.1
27141100
ETIM 4.0
EC000902
UNSPSC 11
39121410
UNSPSC 21.0
39121410
Conductor cross section flexible min.
0.14 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.14 mm²
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.14 mm²
2 conductors with same cross section, stranded max.
1.5 mm²
Internal cylindrical gage
A3
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.1
27141100
ECLASS 9.0
27141126
ETIM 6.0
EC000902
UNSPSC 7.0901
39121410
UNSPSC 18.0
39121410
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 5.0
27141100
ETIM 2.0
EC000902
ETIM 7.0
EC000902
UNSPSC 12.01
39121410
UNSPSC 19.0
39121410