3046346 Phoenix Contact Terminal Blocks

Product Details

• Number of levels
  1
• Flammability rating according to UL 94
  V0
• Note
  The max. current is determined by the diode. Installed: Diode 1N 4007, reverse voltage: 1300 V, maximum continuous current: 0.5 A.
• Insulating material
  PA
• Overvoltage category
  III
• Open side panel
  Yes
• Finger protection
  guaranteed
• Maximum load current
  0.5 A
• Number of connections
  2
• Color
  gray
• Nominal current IN
  0.5 A
• Nominal voltage UN
  800 V
• Result of surge voltage test
  Test passed
• Result of power-frequency withstand voltage test
  Test passed
• Bending test rotation speed
  10 rpm
• Tractive force setpoint
  80 N
• Result of voltage-drop test
  Test passed
• Result of thermal test
  Test passed
• Test specification, oscillation, broadband noise
  DIN EN 50155 (VDE 0115-200):2008-03
• ASD level
  0.02 g²/Hz
Shock form
Half-sine
Surface flammability NFPA 130 (ASTM E 162)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Length
57.8 mm
Height NS 35/15
55 mm
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.14 mm²
2 conductors with same cross section, solid min.
0.14 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, minimum
0.14 mm²
Two conductors with the same cross section stranded, with ferrule and without plastic sleeve, maximum
1.5 mm²
Stripping length
9 mm
Ambient temperature (actuation)
-5 °C ... 70 °C
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Width
6.2 mm
Conductor cross section AWG max.
10
2 conductors with same cross section, stranded min.
0.14 mm²
Connection method
Screw connection
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
REACh SVHC
Lead 7439-92-1
ECLASS 4.1
27141100
ECLASS 7.0
27141127
ETIM 6.0
EC000903
UNSPSC 18.0
39121410
UNSPSC 21.0
39121410
Nominal cross section
4 mm²
Rated surge voltage
8 kV
Maximum power dissipation for nominal condition
1.02 W
Back of the hand protection
guaranteed
Power frequency withstand voltage setpoint
2 kV
Bending test turns
135
Result of tight fit on support
Test passed
Requirements, voltage drop
≤ 3.2 mV
Oscillation, broadband noise test result
Test passed
Acceleration
5g
Shock test result
Test passed
Number of shocks per direction
3
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Conductor cross section solid max.
6 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
4 mm²
2 conductors with same cross section, solid max.
1.5 mm²
Tightening torque, min
0.6 Nm
Connection in acc. with standard
CSA
ECLASS 4.0
27141100
ECLASS 9.0
27141127
UNSPSC 6.01
30211811
UNSPSC 12.01
39121410
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Surge voltage test setpoint
9.8 kV
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Bending test conductor cross section/weight
0.14 mm² / 0.2 kg
Tensile test result
Test passed
Tight fit on carrier
NS 35
Result of temperature-rise test
Test passed
Test frequency
f1 = 5 Hz to f2 = 150 Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Shock duration
30 ms
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
27,5 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Conductor cross section solid min.
0.14 mm²
Conductor cross section AWG min.
26
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.14 mm²
2 conductors with same cross section, stranded max.
1.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
2.5 mm²
Tightening torque max
0.8 Nm
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 10.0.1
27141127
ECLASS 6.0
27141100
ETIM 2.0
EC000897
ETIM 4.0
EC000903
UNSPSC 13.2
39121410
Result of flexion and pull-out test
Test passed
Conductor cross section tensile test
6 mm²
Setpoint
1 N
Proof of thermal characteristics (needle flame) effective duration
30 s
Test spectrum
Service life test category 1, class B, body mounted
Test duration per axis
5 h
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
125 °C
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
End cover width
2.2 mm
Height NS 35/7,5
47.5 mm
Conductor cross section flexible min.
0.14 mm²
Conductor cross section flexible max.
6 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
4 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Internal cylindrical gage
A4
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 5.1
27141100
ETIM 3.0
EC000897
UNSPSC 7.0901
39121410
UNSPSC 20.0
39121410
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 11.0
27141127
ECLASS 5.0
27141100
ETIM 7.0
EC000903
UNSPSC 11
39121410
UNSPSC 19.0
39121410