2902019 Phoenix Contact Electrical Measuring & Monitoring Instruments

2902019 Product Details

• UNSPSC 21.0
  39121008
• UNSPSC 6.01
  30211502
• Depth
  119.2 mm
• Maximum altitude
  ≤ 2000 m
• max. input voltage
  33 V
• Voltage input signal
  -50 mV ... 50 mV (via DIP switch)
• Voltage output signal
  0 V ... 5 V (via DIP switch)
• Ripple
  < 20 mVPP (at 600 Ω)
• Conductor cross section flexible
  0.14 mm² ... 2.5 mm²
• Maximum transmission error
  ≤ 0.1 % (of final value)
• Vibration
  A
• ECLASS 11.0
  27210120
• ECLASS 4.0
  27210100
• ECLASS 10.0.1
  27210120
• Ambient temperature (operation)
  -40 °C ... 70 °C
• Configurable/programmable
  Yes
• Input resistance of voltage input
  > 10 kΩ
• Nominal supply voltage
  24 V DC
• Stripping length
  10 mm
• Conductor cross section AWG
  24 ... 12 (flexible)
Electromagnetic compatibility
Conformance with EMC directive
Rated insulation voltage
300 V
Standards/regulations
EN 61000-4-6
ECLASS 6.0
27210100
ECLASS 9.0
27210120
UNSPSC 11
39121004
UNSPSC 19.0
39121008
Width
6.2 mm
Degree of protection
IP20 (not assessed by UL)
Max. output current
22 mA
Load/output load current output
≤ 600 Ω (at 20 mA)
Power consumption
≤ 800 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)
Screw thread
M3
Torque
0.5 Nm ... 0.6 Nm
Step response (10-90%)
< 8.5 ms (with 30 Hz filter)
EMC
A
ECLASS 4.1
27210100
ETIM 7.0
EC002653
ETIM 4.0
EC002653
UNSPSC 18.0
39121008
Height
109.81 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Number of inputs
1
Number of outputs
1
Load/output load voltage output
≥ 10 kΩ
Supply voltage range
9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
Conductor cross section solid
0.2 mm² ... 1.5 mm² (with ferrule)
Limit frequency (3 dB)
30 Hz (via DIP switch)
Electrical isolation
Reinforced insulation in accordance with IEC 61010-1
Humidity
B
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 5.0
27210100
ECLASS 7.0
27210120
UNSPSC 13.2
39121008
UNSPSC 7.0901
39121004
ECLASS 5.1
27210100
Permissible humidity (operation)
5 % ... 95 % (non-condensing)
ETIM 6.0
EC002653
Noise immunity
EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
Short-circuit current
< 32 mA
Current output signal
0 mA ... 20 mA (via DIP switch)
UNSPSC 12.01
39121004
UNSPSC 20.0
39121008
Typical current consumption
25 mA (Current output, at 24 V DC incl. load)
Connection method
Screw connection
No. of channels
1
Maximum temperature coefficient
0.01 %/K
Housing material
PBT
Noise emission
EN 61000-6-4
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 2
REACh SVHC
Lead 7439-92-1
Enclosure
Required protection according to the Rules shall be provided upon installation on board
Color
gray
Overvoltage category
II
Test voltage, input/output/supply
3 kV (50 Hz, 1 min.)
Temperature
B
Designation
Shipbuilding approval
Certificate
DNV GL TAA00002UA
Protective circuit
Transient protection
Mounting position
any
Assembly instructions
The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
Degree of pollution
2
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 2
Identification
UL 508 Listed
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 2

Product condition