X67BCD321.L12 B&R Electronic Components
Part#:X67BCD321.L12
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
X67 bus controller, 1 EtherNet/IP interface, X2X Link power supply 15 W, 16 digital channels configurable as inputs or outputs, 24 VDC, 0.5 A, configurable input filter, 2 event counters 50 kHz, M12 connectors, high-density module
Check out the X67BCD321.L12 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight355 g
- Torque for connections M12 Max. 0.6 Nm
- Dimensions Depth 42 mm
- Installation elevation above sea level 0 to 2000 m No limitation
- Temperature Transport -40 to 85°C
- Dimensions Width 53 mm
- Dimensions Height 155 mm
- Torque for connections M8 Max. 0.4 Nm
- Temperature Storage -40 to 85°C
- Switching delay 1 → 0 <400 µs
- Installation elevation above sea level >2000 m Reduction of ambient temperature by 0.5°C per 100 m
- Mounting orientation Any Yes
- Temperature Operation -25 to 60°C
- Input filter Software Default 0 ms, configurable between 0 and 25 ms in 0.2 ms intervals
- Switching delay 0 → 1 <400 µs
- Temperature Derating -
- Switching frequency Resistive load Max. 100 Hz
- Power consumption Sensor/Actuator power supply Max. 12 W
- Switching frequency Inductive load See section "Switching inductive loads".
- Input filter Hardware ≤10 μs (channels 1 to 4) / ≤70 µs (channels 5 to 8)
- Counter frequency Internal 48 MHz, 3 MHz, 187.5 kHz
- Min. cycle time X2X Link 500 μs
- Transfer Auto-MDI/MDIX Yes
- Switching threshold High >15 VDC
- Switching threshold Low <5 VDC
- Transfer Half-duplex Yes
- Min. cycle time Fieldbus 1 ms
- Transfer Autonegotiation Yes
- Certifications UL cULus E115267; Industrial control equipment
- B&R ID code Bus controller 0xACF7
- Certifications ATEX Zone 2, II 3G Ex nA IIA T5 Gc; IP67, Ta = 0 - Max. 60°C; TÜV 05 ATEX 7201X
- Transfer Full-duplex Yes
- Diagnostics Outputs Yes, using LED status indicator and software
- Braking voltage when switching off inductive loads 50 VDC
- Certifications KC Yes
- Certifications EAC Yes
- Power consumption Fieldbus 2.5 W
- Residual voltage <0.3 V at 0.5 A nominal current
- Certifications UKCA Yes
- Transfer Physical layer 10BASE-T/100BASE-TX
- Nominal output current 0.5 A
- Certifications HazLoc cCSAus 244665; Process control equipment; for hazardous locations; Class I, Division 2, Groups ABCD, T5
- Power consumption X2X Link power supply 20.5 W at maximum power output for connected I/O modules
- Certifications CE Yes
- Degree of protection per EN 60529 IP67
- Connection type I/O power supply M8, 4-pin
- Power consumption Internal I/O 3.3 W
- Diagnostics I/O power supply Yes, using LED status indicator and software
- B&R ID code Internal I/O module 0xB1E7
- Switching on after overload shutdown Approx. 10 ms (depends on the module temperature)
- Connection type X2X Link M12, B-coded
- Length of pause between pulses ≥100 µs
- Electrical isolation Channel isolated from bus; EtherNet/IP not isolated from bus and channel not isolated from channel
- Input current at 24 VDC Typ. 4 mA
- Pulse length ≥20 µs
- Diagnostic status Output monitoring with 10 ms delay
- Leakage current when the output is switched off 5 µA
- Switching voltage I/O power supply minus residual voltage
- Counter size 16-bit
- Output protection Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads, reverse polarity protection of the output power supply
- Output circuit Source
- Input circuit Sink
- Input characteristics per EN 61131-2 Type 1
- Counter 2 Input 3
- Additional functions 50 kHz event counting, gate measurement
- Bus controller EtherNet/IP Adapter (slave)
- Fieldbus EtherNet/IP Adapter (slave)
- Variant Internal 3x switch, male M12 circular connector, 2 female connectors on the module
- Connection type Inputs/Outputs 8x M12, A-coded
- Connection type Fieldbus M12, D-coded
- Peak short-circuit current <12 A
- Total nominal current 8 A
- Supported inputs Input 2 or input 4
- Counter frequency Max. 50 kHz
- Evaluation Each negative edge, cyclic counter
- Signal form Square wave pulse
- Counter 1 Input 1
- Input frequency Max. 50 kHz
- Quantity 2
- Input resistance Typ. 6 kΩ
- Short-circuit proof Yes
- Input voltage 18 to 30 VDC
- Summation current Max. 0.5 A
- Voltage drop for short-circuit protection at 0.5 A Max. 2 VDC
- Voltage I/O power supply minus voltage drop for short-circuit protection
- Synchronization between bus systems possible No
- Integrated protection Reverse polarity protection
- Voltage range 18 to 30 VDC
- Transfer rate 10/100 Mbit/s
- Line length Max. 100 m between 2 stations (segment length)
- Status indicators I/O function per channel, supply voltage, bus function
- Nominal voltage 24 VDC
- Power output 15 W X2X Link power supply for I/O modules
- Sensor/Actuator power supply 0.5 A summation current
- Insulation voltage between channel and bus 500 Veff
- Inputs/Outputs 16 digital channels, configurable as inputs or outputs using Automation Studio or data point, inputs with additional functions
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨
We are a proud member of:
