X67BC4321.L12-10 B&R Electronic Components
Part#:X67BC4321.L12-10
Manufacturer:B&R
Product Lifecycle:Active
Get a quick Quote!
X67 bus controller, 1 CANopen interface, X2X Link power supply 15 W, 16 digital channels configurable as inputs or outputs, 24 VDC, 0.5 A, configurable input filter, 2 event counters 50 kHz, CAN bus galvanically isolated M12 connectors, high-density modul
Check out the X67BC4321.L12-10 B&R price in the box on the right side or send a quick quote.
Product Details
- Weight300 g
- Dimensions Height 155 mm
- Torque for connections M8 Max. 0.4 Nm
- Dimensions Depth 42 mm
- Torque for connections M12 Max. 0.6 Nm
- Temperature Storage -40 to 85°C
- Dimensions Width 53 mm
- Temperature Operation -25 to 60°C
- Temperature Derating -
- Temperature Transport -40 to 85°C
- Installation elevation above sea level 0 to 2000 m No limitation
- Switching frequency Inductive load See section "Switching inductive loads".
- Counter frequency Internal 48 MHz, 3 MHz, 187.5 kHz
- Switching frequency Resistive load Max. 100 Hz
- Switching delay 0 → 1 <400 µs
- Installation elevation above sea level >2000 m Reduction of ambient temperature by 0.5°C per 100 m
- Mounting orientation Any Yes
- Switching delay 1 → 0 <400 µs
- Switching threshold Low <5 VDC
- Switching threshold High >15 VDC
- Input filter Hardware ≤10 μs (channels 1 to 4) / ≤70 µs (channels 5 to 16)
- Input filter Software Default 0 ms, configurable between 0 and 25 ms in 0.2 ms intervals
- Min. cycle time X2X Link 500 μs
- Certifications KC Yes
- Power consumption Sensor/Actuator power supply Max. 12 W
- Min. cycle time Fieldbus No limitation
- Certifications UL cULus E115267; Industrial control equipment
- Certifications HazLoc cCSAus 244665; Process control equipment; for hazardous locations; Class I, Division 2, Groups ABCD, T5
- Certifications EAC Yes
- Certifications UKCA Yes
- Certifications CE Yes
- Certifications ATEX Zone 2, II 3G Ex nA IIA T5 Gc; IP67, Ta = 0 - Max. 60°C; TÜV 05 ATEX 7201X
- Power consumption Fieldbus 2.11 W
- Connection type I/O power supply M8, 4-pin
- Power consumption Internal I/O 3.71 W
- Power consumption X2X Link power supply 21.59 W at maximum power output for connected I/O modules
- Connection type X2X Link M12, B-coded
- Connection type Inputs/Outputs 8x M12, A-coded
- Connection type Fieldbus M12, A-coded
- Diagnostics I/O power supply Yes, using LED status indicator and software
- Diagnostics Outputs Yes, using LED status indicator and software
- B&R ID code Bus controller 0xB12A
- Leakage current when the output is switched off 5 µA
- Degree of protection per EN 60529 IP67
- Electrical isolation Bus isolated from CANopen and channel; Channel isolated from CANopen; Channel not isolated from channel
- Switching on after overload shutdown Approx. 10 ms (depends on the module temperature)
- Peak short-circuit current <12 A
- Residual voltage <0.3 V at 0.5 A nominal current
- Braking voltage when switching off inductive loads 50 VDC
- Total nominal current 8 A
- Pulse length ≥20 µs
- Nominal output current 0.5 A
- Switching voltage I/O power supply minus residual voltage
- Output circuit Source
- Input frequency Max. 50 kHz
- Counter frequency Max. 50 kHz
- Additional functions 50 kHz event counting, gate measurement
- Input voltage 18 to 30 VDC
- Input characteristics per EN 61131-2 Type 1
- Integrated protection Reverse polarity protection
- Max. distance 1000 m
- Power output 15 W X2X Link power supply for I/O modules
- B&R ID code Internal I/O module 0xB52A
- Diagnostic status Output monitoring with 10 ms delay
- Output protection Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads, reverse polarity protection of the output power supply
- Supported inputs Input 2 or input 4
- Length of pause between pulses ≥100 µs
- Counter 2 Input 3
- Counter size 16-bit
- Counter 1 Input 1
- Evaluation Each negative edge, cyclic counter
- Quantity 2
- Signal form Square wave pulse
- Input resistance Typ. 6 kΩ
- Input circuit Sink
- Input current at 24 VDC Typ. 4 mA
- Summation current Max. 0.5 A
- Short-circuit proof Yes
- Voltage I/O power supply minus voltage drop for short-circuit protection
- Terminating resistor Can be optionally screwed onto the integrated Y-connector
- Voltage drop for short-circuit protection at 0.5 A Max. 2 VDC
- Voltage range 18 to 30 VDC
- Default transfer rate Automatic transfer rate detection
- Transfer rate Max. 1 Mbit/s
- Synchronization between bus systems possible No
- Sensor/Actuator power supply 0.5 A summation current
- Bus controller CANopen
- Inputs/Outputs 16 digital channels, configurable as inputs or outputs using software, inputs with additional functions
- Status indicators I/O function per channel, supply voltage, bus function
- Insulation voltage between channel and bus 500 Veff
- Nominal voltage 24 VDC
- Fieldbus CANopen
- Variant 2x M12 interface for the Y-connector integrated in the module
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of B&R
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
B&R Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many B&R Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from B&R, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨
We are a proud member of:
