X67BC8513.L12 B&R Electronic Components

Product Details

• Weight360 g
• Dimensions Height
  155 mm
• Torque for connections M8
  Max. 0.4 Nm
• Dimensions Depth
  42 mm
• Torque for connections M12
  Max. 0.6 Nm
• Temperature Transport
  -40 to 85°C
• Dimensions Width
  53 mm
• Temperature Storage
  -40 to 85°C
• Temperature Operation
  -25 to 60°C
• Temperature Derating
  -
• Installation elevation above sea level >2000 m
  Reduction of ambient temperature by 0.5°C per 100 m
• Switching delay 0 → 1
  <400 µs
• Switching frequency Inductive load
  See section "Switching inductive loads".
• Installation elevation above sea level 0 to 2000 m
  No limitation
• Switching frequency Resistive load
  Max. 100 Hz
• Mounting orientation Any
  Yes
• Input filter Cutoff frequency
  1 kHz
• Input filter Slope
  40 dB
• Switching delay 1 → 0
  <400 µs
• Output of digital value during overload Overshoot
  0x7FFF
Common-mode rejection DC
>50 dB
Max. error Gain
0.1%
Max. error Offset
0.05%
Common-mode rejection 50 Hz
>50 dB
Output of digital value during overload Undershoot
0x0000
Switching threshold Low
<5 VDC
Switching threshold High
>15 VDC
Counter frequency Internal
48 MHz, 3 MHz, 187.5 kHz
Input filter Software
Default 0 ms, configurable between 0 and 25 ms in 0.2 ms intervals
Output format Current
0x0000 - 0x7FFF / 1 LSB = 0x0008 = 4.883 μA
Input filter Hardware
≤10 μs (channels 1 to 4) / ≤70 µs (channels 5 to 12)
Transfer Auto-MDI/MDIX
Yes
Transfer Autonegotiation
Yes
Min. cycle time Fieldbus
200 μs
Power consumption Sensor/Actuator power supply
Max. 12 W
Transfer Half-duplex
Yes
Transfer Full-duplex
No
Min. cycle time X2X Link
200 μs
Certifications EAC
Yes
Certifications KC
Yes
Certifications ATEX
Zone 2, II 3G Ex nA IIA T5 Gc; IP67, Ta = 0 - Max. 60°C; TÜV 05 ATEX 7201X
Certifications HazLoc
cCSAus 244665; Process control equipment; for hazardous locations; Class I, Division 2, Groups ABCD, T5
Transfer Physical layer
100BASE-TX
Certifications UL
cULus E115267; Industrial control equipment
Certifications CE
Yes
Power consumption X2X Link power supply
17.25 W at maximum power output for connected I/O modules
Power consumption Fieldbus
2.5 W
Certifications UKCA
Yes
Power consumption Internal I/O
0.6 W
Connection type I/O power supply
M8, 4-pin
Connection type Fieldbus
M12, D-coded
Connection type X2X Link
M12, B-coded
Connection type Inputs/Outputs
8x M12, A-coded
Diagnostics I/O power supply
Yes, using LED status indicator and software
B&R ID code Bus controller
0xB3AC
Diagnostics Outputs
Yes, using LED status indicator and software
B&R ID code Internal I/O module
0xB3CD
Degree of protection per EN 60529
IP67
Braking voltage when switching off inductive loads
50 VDC
Electrical isolation
Bus isolated from POWERLINK and channel; Channel not isolated from channel
Type
Type 2
RDS(on)
150 mΩ
Bus controller
POWERLINK (V1/V2) controlled node
Residual voltage
<0.3 V at 0.5 A nominal current
Peak short-circuit current
<12 A
Leakage current when the output is switched off
5 µA
Switching on after overload shutdown
Approx. 10 ms (depends on the module temperature)
Diagnostic status
Output monitoring with 10 ms delay
Total nominal current
8 A
Output protection
Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads, reverse polarity protection of the output power supply
Output circuit
Source
Nominal output current
0.5 A
Voltage drop at 20 mA
Typ. 4.5 V
Fieldbus
POWERLINK (V1/V2) controlled node
Switching voltage
I/O power supply minus residual voltage
Insulation voltage between input and bus
500 Veff
Nonlinearity
<0.1%
Inputs/Outputs
12 digital channels (configurable as inputs or outputs using the software, inputs with additional functions), 1 analog channel
Power output
15 W X2X Link power supply for I/O modules
Max. offset drift
0.02 %/°C
Status indicators
I/O function per channel, supply voltage, bus function
Sensor/Actuator power supply
0.5 A summation current
Common-mode range
±2 V
Max. gain drift
0.013 %/°C
Crosstalk between channels
>70 dB
Insulation voltage between channel and bus
500 Veff
Conversion procedure
Successive approximation
Load
<300 Ω
Permissible input signal
Max. ±30 mA
Output format
INT
Input protection
Protection against wiring with supply voltage
Input type
Differential input
Conversion time
200 µs
Digital converter resolution
12-bit
Supported inputs
Input 2
Input
0 to 20 mA
Nominal voltage
24 VDC
Pulse length
≥20 µs
Counter size
16-bit
Counter frequency
Max. 50 kHz
Evaluation
Each negative edge, cyclic counter
Short-circuit proof
Yes
Integrated protection
Reverse polarity protection
Length of pause between pulses
≥100 µs
Counter 1
Input 1
Input frequency
Max. 50 kHz
Quantity
1
Signal form
Square wave pulse
Additional functions
50 kHz event counting, gate measurement
Input circuit
Sink
Input voltage
18 to 30 VDC
Input characteristics per EN 61131-2
Type 1
Input resistance
Typ. 6 kΩ
Synchronization between bus systems possible
Yes
Voltage
I/O power supply minus voltage drop for short-circuit protection
Input current at 24 VDC
Typ. 4 mA
Summation current
Max. 0.5 A
Voltage drop for short-circuit protection at 0.5 A
Max. 2 VDC
Hub propagation delay
0.96 to 1 µs
Transfer rate
100 Mbit/s
Variant
2x M12 interface (hub), 2x female connector on module
Voltage range
18 to 30 VDC
Line length
Max. 100 m between 2 stations (segment length)

Related documents X67BC8513.L12 Specs