3274210 Phoenix Contact Terminal Blocks

Product Details

• Note
  The max. load current must not be exceeded by the total current of all connected conductors.
• Nominal cross section
  2.5 mm²
• Insulating material
  PA
• Overvoltage category
  III
• Number of connections
  19
• Color
  gray
• Rated surge voltage
  8 kV
• Maximum total current
  57 A (with 10 mm² conductor cross section)
• Back of the hand protection
  guaranteed
• Bending test rotation speed
  10 rpm
• Tensile test result
  Test passed
• Potentials
  1
• Degree of pollution
  3
• Open side panel
  No
• Finger protection
  guaranteed
• Result of tight fit on support
  Test passed
• Conductor cross section short circuit testing
  10 mm²
• Test spectrum
  Service life test category 2, bogie-mounted
• Test specification, shock test
  DIN EN 50155 (VDE 0115-200):2008-03
• Relative insulation material temperature index (Elec., UL 746 B)
  130 °C
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Connection method
Push-in connection
Conductor cross section solid max.
10 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Nominal cross section feed-in
6 mm²
Insulating material group
I
Maximum load current
57 A (with 10 mm² conductor cross section)
Nominal voltage UN
690 V
Power frequency withstand voltage setpoint
1.89 kV
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Setpoint
5 N
Short circuit stability result
Test passed
Ageing test for screwless modular terminal block temperature cycles
192
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Test directions
X-, Y- and Z-axis (pos. and neg.)
Number of shocks per direction
3
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Width
56.5 mm
Number of levels
1
Flammability rating according to UL 94
V0
Maximum power dissipation for nominal condition
1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
Result of power-frequency withstand voltage test
Test passed
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Result of voltage-drop test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
ASD level
6.12 (m/s2)2/Hz
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Stripping length
10 mm ... 12 mm
Nominal current IN
41 A (with 6 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Result of surge voltage test
Test passed
Result of flexion and pull-out test
Test passed
Bending test turns
135
Result of temperature-rise test
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Result of thermal test
Test passed
Result of aging test
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Acceleration
30g
Shock duration
18 ms
Shock form
Half-sine
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Tight fit on carrier
NS 35
Short-time current
1.2 kA
Oscillation, broadband noise test result
Test passed
Test duration per axis
5 h
Shock test result
Test passed
Surface flammability NFPA 130 (ASTM E 162)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Length
28.6 mm
Min. AWG conductor cross section, flexible
20
Conductor cross section flexible max.
10 mm²
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 10.0.1
27141120
Height NS 15
31.4 mm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section flexible min.
0.5 mm²
Connection cross sections directly pluggable
1 mm² 10 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
ECLASS 11.0
27141120
ECLASS 5.1
27141120
ETIM 6.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 20.0
39121410
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Conductor cross section solid min.
1 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 5.0
27141120
UNSPSC 6.01
30211811
UNSPSC 7.0901
39121410
Static insulating material application in cold
-60 °C
Conductor cross section AWG max.
8
Max. AWG conductor cross section, flexible
10
Internal cylindrical gage
A3
Value
1 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 4.0
27141121
ECLASS 6.0
27141100
ECLASS 9.0
27141120
ETIM 7.0
EC000897
UNSPSC 19.0
39121410
Conductor cross section AWG min.
20
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
ECLASS 7.0
27141120
ETIM 3.0
EC000897
UNSPSC 18.0
39121410
Connection
Feed-in stage
Ambient temperature (assembly)
-5 °C ... 70 °C
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 4.1
27141121
ETIM 4.0
EC000897
UNSPSC 11
39121410
UNSPSC 13.2
39121410
UNSPSC 21.0
39121410