3274216 Phoenix Contact Terminal Blocks

Product Details

• Note
  The max. load current must not be exceeded by the total current of all connected conductors.
• Flammability rating according to UL 94
  V0
• Maximum load current
  57 A (with 10 mm² conductor cross section)
• Finger protection
  guaranteed
• Result of tight fit on support
  Test passed
• Setpoint
  5 N
• Short-time current
  1.2 kA
• Ageing test for screwless modular terminal block temperature cycles
  192
• Test frequency
  f1 = 5 Hz to f2 = 250 Hz
• Test specification, shock test
  DIN EN 50155 (VDE 0115-200):2008-03
• Shock duration
  18 ms
• Fire protection for rail vehicles (DIN EN 45545-2) R24
  HL 1 - HL 3
• Length
  28.6 mm
• Connection in acc. with standard
  IEC 60947-7-1
• Conductor cross section flexible, with ferrule without plastic sleeve min.
  0.5 mm²
• Connection cross sections directly pluggable
  1 mm² 10 mm²
• Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
  0.5 mm²
• ECLASS 10.0.1
  27141120
• ECLASS 5.0
  27141120
• ETIM 3.0
  EC000897
UNSPSC 7.0901
39121410
UNSPSC 20.0
39121410
Nominal cross section
2.5 mm²
Rated surge voltage
8 kV
Insulating material
PA
Nominal voltage UN
690 V
Result of surge voltage test
Test passed
Bending test turns
135
Result of flexion and pull-out test
Test passed
Result of voltage-drop test
Test passed
Result of thermal test
Test passed
Result of aging test
Test passed
Test duration per axis
5 h
Test directions
X-, Y- and Z-axis (pos. and neg.)
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Width
56.5 mm
Conductor cross section AWG max.
8
Max. AWG conductor cross section, flexible
10
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Value
1 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 6.0
27141100
ETIM 4.0
EC000897
UNSPSC 6.01
30211811
UNSPSC 19.0
39121410
Number of levels
1
Nominal cross section feed-in
6 mm²
Insulating material group
I
Maximum power dissipation for nominal condition
1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
Open side panel
No
Power frequency withstand voltage setpoint
1.89 kV
Result of power-frequency withstand voltage test
Test passed
Bending test conductor cross section/weight
0.5 mm² / 0.3 kg
Short circuit stability result
Test passed
Conductor cross section short circuit testing
10 mm²
ASD level
6.12 (m/s2)2/Hz
Shock form
Half-sine
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Surface flammability NFPA 130 (ASTM E 162)
passed
Height NS 15
31.4 mm
Conductor cross section solid max.
10 mm²
Conductor cross section flexible max.
10 mm²
Min. AWG conductor cross section, flexible
20
Connection
Feed-in stage
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
ECLASS 4.0
27141121
ECLASS 9.0
27141120
ETIM 7.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 21.0
39121410
Potentials
1
Degree of pollution
3
Maximum total current
57 A (with 10 mm² conductor cross section)
Back of the hand protection
guaranteed
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Tensile test result
Test passed
Result of temperature-rise test
Test passed
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Test spectrum
Service life test category 2, bogie-mounted
Acceleration
30g
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Connection method
Push-in connection
Stripping length
10 mm ... 12 mm
Conductor cross section AWG min.
20
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Ambient temperature (assembly)
-5 °C ... 70 °C
ECLASS 11.0
27141120
ECLASS 7.0
27141120
ECLASS 4.1
27141121
UNSPSC 13.2
39121410
UNSPSC 18.0
39121410
Number of connections
19
Nominal current IN
41 A (with 6 mm² conductor cross section)
Shock protection test specification
DIN EN 50274 (VDE 0660-514):2002-11
Bending test rotation speed
10 rpm
Tight fit on carrier
NS 35
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Proof of thermal characteristics (needle flame) effective duration
30 s
Oscillation, broadband noise test result
Test passed
Shock test result
Test passed
Number of shocks per direction
3
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Conductor cross section solid min.
1 mm²
Conductor cross section flexible min.
0.5 mm²
Color
yellow
Internal cylindrical gage
A3
UNSPSC 11
39121410
Ambient temperature (actuation)
-5 °C ... 70 °C
ETIM 6.0
EC000897
Overvoltage category
III
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 5.1
27141120