2903145 Phoenix Contact AC/DC Power Supplies

2903145 Product Details

• Height
  130 mm
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
• Installation height
  ≤ 5000 m (> 2000 m, observe derating)
• AC frequency range
  50 Hz ... 60 Hz ±5 Hz
• Recommended breaker for input protection
  6 A ... 16 A (Characteristics B, C, D, K)
• Protective circuit/component
  Varistor
• Setting range of the output voltage (USet)
  24 V DC ... 28 V DC (constant capacity)
• Derating
  > 60 °C ... 70 °C (2.5%/K)
• Feedback voltage resistance
  ≤ 35 V DC
• Net weight
  1 kg
• Conductor cross section solid max.
  1.5 mm²
• Stripping length
  8 mm
• Standard – Safety extra-low voltage
  IEC 60950-1 (SELV) and EN 60204-1 (PELV)
• Mains variation/undervoltage
  Semi F47-0706
• Electrostatic discharge
  EN 61000-4-2
• Frequency range
  0.15 MHz ... 80 MHz
• Voltage
  10 V (Test Level 3)
• ECLASS 10.0.1
  27040701
• ECLASS 4.0
  27040700
• ECLASS 9.0
  27040701
ETIM 7.0
EC002540
UNSPSC 11
39121004
UNSPSC 21.0
39121004
Depth
160 mm
Degree of protection
IP20
Ambient temperature (start-up type tested)
-40 °C
Climatic class
3K3 (in acc. with EN 60721)
Dielectric strength maximum
300 V AC 15 s
Frequency range (fN)
50 Hz ... 60 Hz ±10 %
Mains buffering time
typ. 20 ms (120 V AC)
Type of protection
Transient surge protection
Dynamic Boost (IDyn.Boost)
15 A (5 s)
Protection against overvoltage at the output (OVP)
≤ 30 V DC
Residual ripple
< 20 mVPP (with nominal values)
Mounting position
horizontal DIN rail NS 35, EN 60715
Connection method
Push-in connection
Standard - Safety of transformers
EN 61558-2-16 (air clearances and creepage distances only)
Standard - Safe isolation
DIN VDE 0100-410
UL approvals
UL Listed UL 508
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Output
1 kV (Test Level 2 - symmetrical)
Width
42 mm
Installation distance right/left
0 mm / 0 mm
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Nominal input voltage range
100 V AC ... 240 V AC
Current consumption
3.1 A (100 V AC)
Nominal power consumption
285 VA
Input fuse
6.3 A (internal (device protection))
Nominal output current (IN)
10 A
Connection in series
yes
Output power
240 W
Maximum power dissipation in no-load condition
< 5.1 W
Efficiency
typ. 90 % (120 V AC)
Assembly instructions
alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm
Conductor cross section flexible min.
0.2 mm²
EMC requirements for noise emission
EN 61000-6-3
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Shipbuilding approval
DNV GL (EMC B)
Discharge in air
8 kV (Test Level 4)
Test field strength
10 V/m (Test Level 3)
Conducted interference
EN 61000-4-6
REACh SVHC
Lead 7439-92-1
ECLASS 4.1
27040700
ECLASS 7.0
27049002
ETIM 4.0
EC000599
UNSPSC 12.01
39121004
Typical response time
< 1 s
Insulation voltage input/output
3 kV AC (type test)
Conductor cross section solid min.
0.2 mm²
Conductor cross section AWG min.
24
Conductor cross section AWG max.
16
Standard - Electrical safety
IEC 60950-1/VDE 0805 (SELV)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Electromagnetic HF field
EN 61000-4-3
Fast transients (burst)
EN 61000-4-4
Input
2 kV (Test Level 3 - symmetrical)
ECLASS 5.0
27049000
ETIM 3.0
EC001039
UNSPSC 7.0901
39121004
UNSPSC 13.2
39121004
Installation distance top/bottom
50 mm / 50 mm
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Degree of pollution
2
Input voltage range
100 V AC ... 240 V AC -15 % ... +10 %
Discharge current to PE
< 3.5 mA
Inrush current
typ. 20 A
Power factor (cos phi)
0.93
Nominal output voltage
24 V DC ±1 %
Connection in parallel
Yes, for redundancy and increased capacity
Control deviation
< 1 % (change in load, static 10 % ... 90 %)
Power loss nominal load max.
< 25 W
MTBF (IEC 61709, SN 29500)
> 1800000 h (25 °C)
Protection class
I (in closed control cabinet)
Conductor cross section flexible max.
1.5 mm²
EMC requirements for noise immunity
EN 61000-6-1
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Rail applications
EN 50121-4
Contact discharge
6 kV (Test Level 4)
Comments
Criterion A
Signal
1 kV (Test Level 2 - asymmetrical)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 11.0
27040701
ECLASS 5.1
27049000
ETIM 6.0
EC002540
UNSPSC 19.0
39121004
Surge voltage load (surge)
EN 61000-4-5
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 6.0
27049000
UNSPSC 6.01
30211502
UNSPSC 18.0
39121004
UNSPSC 20.0
39121004

Product condition