2903153 Phoenix Contact AC/DC Power Supplies

2903153 Product Details

• Depth
  115 mm
• Inflammability class in acc. with UL 94 (housing / terminal blocks)
  V0
• Installation height
  ≤ 5000 m (> 2000 m, Derating: 10 %/1000 m)
• Input fuse
  3.15 A (internal (device protection), slow-blow)
• Protective circuit/component
  Varistor
• Width
  35 mm
• Installation distance right/left
  0 mm / 0 mm
• Height
  130 mm
• Max. permissible relative humidity (operation)
  ≤ 95 % (at 25 °C, non-condensing)
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Input voltage range
  3x 400 V AC ... 500 V AC -20 % ....+15 %
• AC frequency range
  50 Hz ... 60 Hz
• Inrush current
  ≤ 22 A (typical)
• Nominal output voltage
  24 V DC ±1 %
• Nominal output current (IN)
  5 A
• Control deviation
  < 1 % (change in load, static 10 % ... 90 %)
• Maximum power dissipation in no-load condition
  < 1 W (400 V AC)
• Insulation voltage input/output
  3 kV AC (type test)
• Conductor cross section flexible min.
  0.2 mm²
• EMC requirements for noise emission
  EN 61000-6-3
Standard - Electrical safety
IEC 60950-1/VDE 0805 (SELV)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Contact discharge
6 kV (Test Level 4)
Frequency range
0.15 MHz ... 80 MHz
Input
3 kV (Test Level 3 - symmetrical)
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 4.0
27040700
ETIM 4.0
EC002540
UNSPSC 13.2
39121004
Installation distance top/bottom
50 mm / 50 mm
Climatic class
3K3 (in acc. with EN 60721)
Nominal input voltage range
3x 400 V AC ... 500 V AC
Nominal power consumption
243.6 VA
Power factor (cos phi)
0.55
Setting range of the output voltage (USet)
24 V DC ... 28 V DC (> 24 V DC, constant capacity restricted)
Derating
> 60 °C ... 70 °C (2.5%/K)
Protection against overvoltage at the output (OVP)
≤ 30 V DC
Typical response time
< 1 s
Efficiency
> 91 % (at 400 V AC and nominal values)
Conductor cross section solid max.
1.5 mm²
Stripping length
8 mm
EMC requirements for noise immunity
EN 61000-6-1
UL approvals
UL Listed UL 508
Electrostatic discharge
EN 61000-4-2
Comments
Criterion A
Output
1 kV (Test Level 2 - symmetrical)
ECLASS 11.0
27040701
ECLASS 7.0
27049002
ETIM 6.0
EC002540
UNSPSC 18.0
39121004
UNSPSC 21.0
39121004
Degree of protection
IP20
Ambient temperature (start-up type tested)
-25 °C
Degree of pollution
2
Current consumption
3x 0.4 A (400 V AC)
Recommended breaker for input protection
6 A ... 16 A (Characteristics B, C, D, K)
Dynamic Boost (IDyn.Boost)
7.5 A (5 s)
Output power
120 W
Power loss nominal load max.
< 12 W (480 V AC)
Connection method
Push-in connection
Conductor cross section solid min.
0.2 mm²
Standard - Safety of transformers
EN 61558-2-16 (air clearances and creepage distances only)
Rail applications
EN 50121-4
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Electromagnetic HF field
EN 61000-4-3
Surge voltage load (surge)
EN 61000-4-5
Criterion A
Normal operating behavior within the specified limits.
REACh SVHC
Lead 7439-92-1
ECLASS 4.1
27040700
ECLASS 6.0
27049000
UNSPSC 20.0
39121004
Ambient temperature (operation)
-25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
Discharge current to PE
< 0.25 mA
Mains buffering time
typ. 20 ms (400 V AC)
Type of protection
Transient surge protection
Connection in series
yes
Connection in parallel
Yes, for redundancy and increased capacity
MTBF (IEC 61709, SN 29500)
> 2300000 h (25 °C)
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section AWG min.
24
Conductor cross section AWG max.
16
Standard - Safe isolation
DIN VDE 0100-410
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Discharge in air
8 kV (Test Level 4)
Test field strength
10 V/m (Test Level 3)
Signal
1 kV (Test Level 1 - symmetrical)
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 5.1
27049000
ETIM 7.0
EC002540
UNSPSC 19.0
39121004
Residual ripple
≤ 20 mVPP
Net weight
0.4 kg
Protection class
II (in closed control cabinet)
Assembly instructions
alignable: horizontally 0 mm (≤ 40 °C) 10 mm (≤ 70 °C), vertically 50 mm
Conductor cross section flexible max.
1.5 mm²
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Standard – Safety extra-low voltage
IEC 60950-1 (SELV) and EN 60204-1 (PELV)
Conducted noise emission
EN 55016
Fast transients (burst)
EN 61000-4-4
Voltage
10 V (Test Level 3)
Conducted interference
EN 61000-4-6
ECLASS 10.0.1
27040701
ECLASS 5.0
27049000
ECLASS 9.0
27040701

Product condition