2902052 Phoenix Contact Electrical Measuring & Monitoring Instruments
Part#:2902052
Manufacturer:Phoenix Contact
Product Lifecycle:Active
Get a quick Quote!
Configurable temperature transducer with plug-in connection technology for connecting 2, 3, and 4-conductor resistance thermometers and resistance-type sensors. Configurable via DIP switch or software. push-in connection technology, standard configuration
About the manufacturer: Phoenix Contact is one of the manufacturers that offers Electrical Measuring & Monitoring Instruments that you can order at Quotebeam.com. Phoenix Contact manufactures industrial electrical and electronic technology products that offer power, protection, connectivity, and automation for systems and equipment.
Check out the 2902052 Phoenix Contact price in the box on the right side or send a quick quote.
Product Details
- Width 6.2 mm
- Degree of protection IP20 (not assessed by UL)
- Linear resistance measuring range 0 Ω ... 4000 Ω (Minimum measuring span: 10% of the selected measuring range)
- Number of outputs 1
- Load/output load current output ≤ 600 Ω (at 20 mA)
- Typical current consumption 32 mA (24 V DC)
- Transmission error resistance-type sensor 2 Ω
- Housing material PBT
- Ambient temperature (operation) -40 °C ... 70 °C
- Noise immunity EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
- Voltage output signal 0 V ... 5 V (via DIP switch)
- China RoHS Environmentally Friendly Use Period = 50 years
- Ambient temperature (storage/transport) -40 °C ... 85 °C
- Current output signal 0 mA ... 20 mA (via DIP switch)
- Depth 119.2 mm
- Temperature measuring range -200 °C ... 850 °C (Range depends on sensor type, range can be set freely via software or in increments from -150°C to 850°C via DIP switches)
- Max. output voltage approx. 12.3 V
- Overvoltage category II
- Test voltage, input/output/supply 3 kV (50 Hz, 1 min.)
- Ripple < 10 mVrms
- Conductor cross section solid 0.2 mm² ... 2.5 mm² (with ferrule)
- Transmission error resistance thermometer 0.1 % * 350 K / set measuring range; 0.1 % > 350 K (Pt/Ni)
- Electrical isolation Reinforced insulation in accordance with IEC 61010-1
- Sensor input current approx. 200 µA
- ETIM 4.0 EC001446
- ETIM 6.0 EC002919
- Connection method Push-in connection
- Supply voltage range 9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
- Max. output current 24.6 mA
- ECLASS 10.0.1 27210129
- ECLASS 5.0 27200200
- UNSPSC 11 39121008
- Typical deviation from the measuring range final value 0.07 %
- Certificate DNV GL 14445-15HH
- UNSPSC 21.0 41112105
- UL, USA/Canada UL 508 Listed
- Utilization restriction EMC: class A product, see manufacturer's declaration in the download area
- Maximum temperature coefficient 0.01 %/K
- Rated insulation voltage 300 V (effective)
- Fire protection for rail vehicles (DIN EN 45545-2) R23 HL 1 - HL 2
- ECLASS 11.0 27210129
- ECLASS 9.0 27210129
- ETIM 7.0 EC002919
- UNSPSC 20.0 41112105
- Conductor cross section flexible 0.14 mm² ... 2.5 mm²
- Degree of pollution 2
- Mounting position any
- Fire protection for rail vehicles (DIN EN 45545-2) R22 HL 1 - HL 2
- Conformance CE-compliant
- REACh SVHC Lead 7439-92-1
- UNSPSC 19.0 41112105
- Configurable/programmable Yes
- Load/output load voltage output ≥ 10 kΩ
- Stripping length 10 mm
- Protective circuit Transient protection
- Standards/regulations EN 61000-4-6
- ATEX II 3 G Ex nA IIC T4 Gc X
- Identification C, EMC2
- ECLASS 5.1 27200200
- ECLASS 7.0 27200206
- UNSPSC 18.0 41112105
- Sensor types (RTD) that can be used Pt, Ni, Cu sensors
- Short-circuit current < 31.5 mA
- Power consumption ≤ 850 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)
- Electromagnetic compatibility Conformance with EMC directive
- Fire protection for rail vehicles (DIN EN 45545-2) R24 HL 1 - HL 2
- ECLASS 4.1 27200200
- ETIM 2.0 EC001446
- UNSPSC 7.0901 39121008
- UNSPSC 13.2 41112105
- Height 109.81 mm
- Permissible humidity (operation) 5 % ... 95 % (non-condensing)
- Connection technology 2-, 3-, 4-conductor
- Conductor cross section AWG 24 ... 12 (flexible)
- Noise emission EN 61000-6-4
- Assembly instructions The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
- Designation Shipbuilding approval
- ECLASS 4.0 27200200
- ECLASS 6.0 27200200
- ETIM 3.0 EC001446
- UNSPSC 6.01 30211506
- UNSPSC 12.01 39121008
Product condition
ORIGINAL PACKAGING
SURPLUS ORIGINAL PACKAGING - 100% unused and in original packaging
1-year warranty
Get a quick Quote!
Request a quote, and we will send you price and availability within minutes.
Select Qty:
Average response time: 11 minutes
By purchasing this item, you agree to the Terms & Conditions
Quotebeam is NOT an authorized distributor of Phoenix Contact
Shipping and Delivery Worldwide
calculate costs and time
Secure Payment Processing
with money back guarantee
1 year warranty
on all parts
Responsive Customer Support
we're here to help!
Need more details?
Feel free to chat with us or check our FAQ
Phoenix Contact Disclaimer:
The product is unused surplus. Quotebeam is not an authorized surplus dealer or affiliate for the Manufacturer of this product. Products may feature older date codes or be from an earlier series than what is currently available from the manufacturer or authorized dealers. Because Quotebeam is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Phoenix Contact Controls products will have firmware already installed, Quotebeam makes no representation as to whether a Controls product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Quotebeam also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Phoenix Contact, its distributors, or any other source. Quotebeam also makes no representations as to your right to install any such firmware on the product. Quotebeam will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Relevant products
Do you have questions?
We’re here for you ✨
We are a proud member of:
