2902020 Phoenix Contact Electrical Measuring & Monitoring Instruments

2902020 Product Details

• Depth
  119.2 mm
• Permissible humidity (operation)
  5 % ... 95 % (non-condensing)
• Width
  6.2 mm
• Ambient temperature (operation)
  -40 °C ... 70 °C
• Degree of protection
  IP20 (not assessed by UL)
• Configurable/programmable
  Yes
• Input resistance of voltage input
  > 10 kΩ
• Voltage output signal
  0 V ... 5 V (via DIP switch)
• Load/output load current output
  ≤ 600 Ω (at 20 mA)
• Supply voltage range
  9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
• Stripping length
  10 mm
• Conductor cross section solid
  0.2 mm² ... 2.5 mm² (with ferrule)
• No. of channels
  1
• Protective circuit
  Transient protection
• Degree of pollution
  2
• Test voltage, input/output/supply
  3 kV (50 Hz, 1 min.)
• Color
  gray
• Designation
  Shipbuilding approval
• Standards/regulations
  EN 61000-4-6
• Temperature
  B
Vibration
A
ECLASS 10.0.1
27210120
ECLASS 11.0
27210120
ETIM 7.0
EC002653
Height
109.81 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Number of inputs
1
max. input voltage
33 V
Number of outputs
1
Max. output current
22 mA
Load/output load voltage output
≥ 10 kΩ
Nominal supply voltage
24 V DC
Typical current consumption
25 mA (Current output, at 24 V DC incl. load)
Connection method
Push-in connection
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
Maximum temperature coefficient
0.01 %/K
Limit frequency (3 dB)
30 Hz (via DIP switch)
Overvoltage category
II
Electromagnetic compatibility
Conformance with EMC directive
Noise emission
EN 61000-6-4
Assembly instructions
The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
Certificate
DNV GL TAA00002UA
Humidity
B
Enclosure
Required protection according to the Rules shall be provided upon installation on board
ECLASS 9.0
27210120
Noise immunity
EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
Voltage input signal
-50 mV ... 50 mV (via DIP switch)
Current output signal
0 mA ... 20 mA (via DIP switch)
Short-circuit current
< 32 mA
Ripple
< 20 mVPP (at 600 Ω)
Power consumption
≤ 800 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)
Conductor cross section AWG
24 ... 12 (flexible)
Maximum transmission error
≤ 0.1 % (of final value)
Step response (10-90%)
< 8.5 ms (with 30 Hz filter)
Electrical isolation
Reinforced insulation in accordance with IEC 61010-1
Rated insulation voltage
300 V
Housing material
PBT
Mounting position
any
Identification
UL 508 Listed
EMC
A
REACh SVHC
Lead 7439-92-1
ETIM 6.0
EC002653

Product condition