2902018 Phoenix Contact Electrical Measuring & Monitoring Instruments

2902018 Product Details

• Height
  109.81 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Number of inputs
  1
• Input resistance of voltage input
  > 10 kΩ
• Max. output current
  22 mA
• Typical current consumption
  25 mA (Current output, at 24 V DC incl. load)
• Screw thread
  M3
• No. of channels
  1
• Limit frequency (3 dB)
  30 Hz (via DIP switch)
• Depth
  119.2 mm
• Degree of protection
  IP20 (not assessed by UL)
• Voltage input signal
  -50 mV ... 50 mV (via DIP switch)
• Number of outputs
  1
• Short-circuit current
  < 32 mA
• Load/output load current output
  ≤ 600 Ω (at 20 mA)
• Supply voltage range
  9.6 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2 TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715))
• Conductor cross section solid
  0.2 mm² ... 1.5 mm² (with ferrule)
• Torque
  0.5 Nm ... 0.6 Nm
• Maximum transmission error
  ≤ 0.1 % (of final value)
• Step response (10-90%)
  < 8.5 ms (with 30 Hz filter)
Noise emission
EN 61000-6-4
Mounting position
any
Standards/regulations
EN 61000-4-6
Humidity
B
Enclosure
Required protection according to the Rules shall be provided upon installation on board
ECLASS 11.0
27210120
Width
6.2 mm
Permissible humidity (operation)
5 % ... 95 % (non-condensing)
Noise immunity
EN 61000-6-2 When being exposed to interference, there may be minimal deviations.
max. input voltage
33 V
Load/output load voltage output
≥ 10 kΩ
Ripple
< 20 mVPP (at 600 Ω)
Connection method
Screw connection
Conductor cross section flexible
0.14 mm² ... 2.5 mm²
Maximum temperature coefficient
0.01 %/K
Protective circuit
Transient protection
Degree of pollution
2
Housing material
PBT
Assembly instructions
The T connector can be used to bridge the supply voltage. It can be snapped onto a 35 mm DIN rail according to EN 60715.
Certificate
DNV GL TAA00002UA
EMC
A
ECLASS 9.0
27210120
Ambient temperature (operation)
-40 °C ... 70 °C
Configurable/programmable
Yes
Voltage output signal
0 V ... 5 V (via DIP switch)
Current output signal
0 mA ... 20 mA (via DIP switch)
Nominal supply voltage
24 V DC
Power consumption
≤ 800 mW (at IOUT = 20 mA, 9.6 V DC, 600 Ω load)
Stripping length
10 mm
Conductor cross section AWG
24 ... 12 (flexible)
Electrical isolation
Reinforced insulation in accordance with IEC 61010-1
Electromagnetic compatibility
Conformance with EMC directive
Color
gray
Designation
Shipbuilding approval
Vibration
A
ECLASS 10.0.1
27210120
ETIM 6.0
EC002653
Overvoltage category
II
Rated insulation voltage
300 V
Test voltage, input/output/supply
3 kV (50 Hz, 1 min.)
Identification
UL 508 Listed
Temperature
B
REACh SVHC
Lead 7439-92-1
ETIM 7.0
EC002653

Product condition