8069727 Festo Pneumatic Components

8069727 Product Details

• Additional functions
  Conformance class B SNMP
• Type code
  EMCA
• Performance Level (PL)
  Safe torque off (STO)/category 3, performance level d
• Nominal rotary speed
  3100 1/min
• Diagnostic coverage
  90 %
• Max. positive test pulse with 0 signal
  10000 µs
• KC characters
  KC EMC
• Configuration support
  GSDML file
• Rotor position sensor
  Absolute encoder, multi-turn
• Media redundancy
  MRP
• Minimum cycle time
  2 ms
• Safety function
  Safe torque off (STO)
• Braking resistor, external
  6 Ohm
• Degree of protection
  IP54
• Peak torque
  0.85 Nm
• PFD
  1.86E-5
• Ethernet, supported protocols
  TCP/IP
• Note on materials
  Contains paint-wetting impairment substances RoHS-compliant
• Baud rate
  10/100 Mbit/s (full/half)
• Rotor position sensor measuring principle
  Magnetic
IP address allocation
FCT DCP
Topologies
Star Line
Controller operating mode
PWM MOSFET power output stage PI current regulator
Protective function
I²t monitoring Software end position detection
Characteristics of digital logic outputs
Freely configurable in some cases Not galvanically isolated
Safety integrity level (SIL)
Safe torque off (STO)/SIL 2
Max. rotational speed
3500 1/min
Max. current of digital logic outputs
100 mA
DC nominal voltage
24 V
Max. number of positioning sets
64
Peak current
10.2 A
Vibration resistance
Transport application test with severity level 2 as per FN 942017-4 and EN 60068-2-6
Note on ambient temperature
Above an ambient temperature of 20 °C, the power must be reduced by 1.75% per °C.
Rotor mass moment of inertia
0.175 kgcm²
PFH
1.0E-9
Display
LED
Hardware fault tolerance
1
Max. negative test pulse on 1 signal
600 µs
Protocol
PROFINET
Rotor position sensor resolution
12 bit
Motor peak power
158 W
Storage temperature
-25 °C ... 70 °C
Nominal torque
0.37 Nm
Proof test interval
20 y
Communication profile
FHPP
Motor nominal power
120 W
Nominal current
6.9 A
SFF safe failure fraction
> 90 %
Permissible voltage fluctuations
+/- 20 %
CE marking (see declaration of conformity)
As per EU EMC directive as per EU machinery directive
Ambient temperature
0 °C ... 50 °C
Relative air humidity
0 - 95 % Non-condensing
Permissible radial shaft load
100 N
Product weight
1925 g
Work range of logic input
24 V
Switching logic at outputs
PNP (positive switching)
Parameterization interface
Ethernet
Absolute encoder operating time
With external battery: max. 6 months Note: the maximum service life of the battery depends its state of charge, the ambient temperature and ageing effects. Without external battery: 3 days (worst case) up to a maximum of 7 days (best case) Note: Maximum s
Certificate issuing authority
German Technical Control Board (TÜV) 01/205/5514.00/16 UL E331130
Shock resistance
Shock test with severity level 2 as per FN 942017-5 and EN 60068-2-27
Certification
RCM compliance mark c UL us - Recognized (OL)
Permissible axial shaft load
60 N
Number of digital logic inputs
2
Characteristics of logic input
Galvanically connected to logic potential
Type of mounting
Screwed tightly With through-hole
Number of digital logic outputs 24 V DC
2
Logic input specification
Based on IEC 61131-2
Input switching logic
PNP (positive switching)

Product condition

Related documents 8069727 Specs