3274218 Phoenix Contact Terminal Blocks

Product Details

• ECLASS 9.0
  27141120
• Number of levels
  1
• Degree of pollution
  3
• Flammability rating according to UL 94
  V0
• Maximum total current
  57 A (with 10 mm² conductor cross section)
• Result of surge voltage test
  Test passed
• Bending test conductor cross section/weight
  0.5 mm² / 0.3 kg
• Setpoint
  5 N
• Conductor cross section short circuit testing
  10 mm²
• Note
  The max. load current must not be exceeded by the total current of all connected conductors.
• Color
  green
• Overvoltage category
  III
• Nominal current IN
  41 A (with 6 mm² conductor cross section)
• Shock protection test specification
  DIN EN 50274 (VDE 0660-514):2002-11
• Result of flexion and pull-out test
  Test passed
• ECLASS 5.1
  27141120
• Nominal cross section
  2.5 mm²
• Rated surge voltage
  8 kV
• Maximum power dissipation for nominal condition
  1.31 W (the value is based on one connection block and is multiplied according to the pin assignment)
• Open side panel
  No
Back of the hand protection
guaranteed
Bending test turns
135
Result of voltage-drop test
Test passed
Short circuit stability result
Test passed
Result of thermal test
Test passed
Operating temperature
-60 °C ... 105 °C (max. short-term operating temperature 130°C)
China RoHS
Environmentally friendly use period: unlimited = EFUP-e
ECLASS 11.0
27141120
ETIM 4.0
EC000897
UNSPSC 7.0901
39121410
UNSPSC 20.0
39121410
Potentials
1
Insulating material
PA
Result of the test for mechanical stability of terminal points (5 x conductor connection)
Test passed
Tensile test result
Test passed
Result of tight fit on support
Test passed
Requirement temperature-rise test
Increase in temperature ≤ 45 K
Short-time current
1.2 kA
Ageing test for screwless modular terminal block temperature cycles
192
Test spectrum
Service life test category 2, bogie-mounted
ASD level
6.12 (m/s2)2/Hz
Acceleration
30g
Number of connections
19
Nominal cross section feed-in
6 mm²
Insulating material group
I
Finger protection
guaranteed
Oscillation, broadband noise test result
Test passed
Test frequency
f1 = 5 Hz to f2 = 250 Hz
Test directions
X-, Y- and Z-axis (pos. and neg.)
Relative insulation material temperature index (Elec., UL 746 B)
130 °C
Specific optical density of smoke NFPA 130 (ASTM E 662)
passed
Smoke gas toxicity NFPA 130 (SMP 800C)
passed
Fire protection for rail vehicles (DIN EN 45545-2) R24
HL 1 - HL 3
Length
28.6 mm
Width
56.5 mm
Conductor cross section solid min.
1 mm²
Conductor cross section flexible max.
10 mm²
Min. AWG conductor cross section, flexible
20
Conductor cross section flexible, with ferrule with plastic sleeve max.
6 mm²
Conductor cross section flexible, with ferrule with plastic sleeve min.
0.5 mm²
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, maximum
1.5 mm²
Ambient temperature (storage/transport)
-25 °C ... 60 °C (for a short time, not exceeding 24 h, -60 °C to +70 °C)
Ambient temperature (assembly)
-5 °C ... 70 °C
Ambient temperature (actuation)
-5 °C ... 70 °C
ECLASS 4.1
27141121
ECLASS 6.0
27141100
UNSPSC 6.01
30211811
UNSPSC 18.0
39121410
UNSPSC 13.2
39121410
Maximum load current
57 A (with 10 mm² conductor cross section)
Nominal voltage UN
690 V
Power frequency withstand voltage setpoint
1.89 kV
Result of power-frequency withstand voltage test
Test passed
Bending test rotation speed
10 rpm
Tight fit on carrier
NS 35
Result of temperature-rise test
Test passed
Result of aging test
Test passed
Proof of thermal characteristics (needle flame) effective duration
30 s
Test specification, oscillation, broadband noise
DIN EN 50155 (VDE 0115-200):2008-03
Test duration per axis
5 h
Shock test result
Test passed
Shock form
Half-sine
Shock duration
18 ms
Temperature index of insulation material (DIN EN 60216-1 (VDE 0304-21))
130 °C
Fire protection for rail vehicles (DIN EN 45545-2) R22
HL 1 - HL 3
Calorimetric heat release NFPA 130 (ASTM E 1354)
28 MJ/kg
Height NS 15
31.4 mm
Connection method
Push-in connection
Conductor cross section AWG min.
20
Conductor cross section flexible min.
0.5 mm²
Conductor cross section AWG max.
8
Max. AWG conductor cross section, flexible
10
Internal cylindrical gage
A3
Value
1 mm²
ECLASS 10.0.1
27141120
ECLASS 5.0
27141120
ECLASS 7.0
27141120
ETIM 6.0
EC000897
UNSPSC 11
39121410
UNSPSC 19.0
39121410
Test specification, shock test
DIN EN 50155 (VDE 0115-200):2008-03
Number of shocks per direction
3
Surface flammability NFPA 130 (ASTM E 162)
passed
Static insulating material application in cold
-60 °C
Fire protection for rail vehicles (DIN EN 45545-2) R23
HL 1 - HL 3
Fire protection for rail vehicles (DIN EN 45545-2) R26
HL 1 - HL 3
Stripping length
10 mm ... 12 mm
Connection in acc. with standard
IEC 60947-7-1
Conductor cross section solid max.
10 mm²
Conductor cross section flexible, with ferrule without plastic sleeve min.
0.5 mm²
Conductor cross section flexible, with ferrule without plastic sleeve max.
6 mm²
Connection cross sections directly pluggable
1 mm² 10 mm²
Connection
Feed-in stage
Two conductors with the same cross section, flexible, with TWIN ferrules, with plastic sleeve, minimum
0.5 mm²
Permissible humidity (storage/transport)
30 % ... 70 %
ECLASS 4.0
27141121
ETIM 3.0
EC000897
ETIM 7.0
EC000897
UNSPSC 12.01
39121410
UNSPSC 21.0
39121410