2866789 Phoenix Contact AC/DC Power Supplies

2866789 Product Details

• Height
  130 mm
• Installation distance top/bottom
  50 mm / 50 mm
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Input voltage range
  85 V AC ... 264 V AC
• Depth
  125 mm
• Depth with alternative assembly
  183 mm
• Ambient temperature (operation)
  -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
• Climatic class
  3K3 (in acc. with EN 60721)
• Nominal input voltage range
  100 V AC ... 240 V AC
• Mains buffering time
  > 35 ms (120 V AC)
• Type of protection
  Transient surge protection
• Nominal output voltage
  24 V DC ±1 %
• Connection in parallel
  Yes, for redundancy and increased capacity
• Maximum power dissipation in no-load condition
  14 W
• MTBF (IEC 61709, SN 29500)
  > 900000 h (25 °C)
• Protection class
  I
• Conductor cross section solid min.
  0.2 mm²
• Screw thread
  M3
• Standard – Safety extra-low voltage
  IEC 60950-1 (SELV) and EN 60204-1 (PELV)
• Width with alternative assembly
  122 mm
Ambient temperature (start-up type tested)
-40 °C
Max. permissible relative humidity (operation)
≤ 95 % (at 25 °C, non-condensing)
Discharge current to PE
< 3.5 mA
Recommended breaker for input protection
16 A ... 20 A (AC: Characteristics B, C, D, K)
Nominal output current (IN)
40 A (-25 °C ... 60 °C, UOUT = 24 V DC)
Protection against overvoltage at the output (OVP)
< 35 V DC
Output power
960 W
Insulation voltage output / PE
500 V DC (routine test)
Conductor cross section solid max.
6 mm²
Stripping length
10 mm
Standard – Limitation of mains harmonic currents
EN 61000-3-2
Electromagnetic compatibility
Conformance with EMC Directive 2014/30/EU
Width
180 mm
Height with alternative assembly
130 mm
Degree of pollution
2
Dielectric strength maximum
300 V AC
Frequency range DC
0 Hz
Input fuse
20 A (slow-blow, internal)
Setting range of the output voltage (USet)
18 V DC ... 29.5 V DC (> 24 V DC, constant capacity restricted)
Selective Fuse Breaking (ISFB)
215 A (12 ms)
Feedback voltage resistance
max. 35 V DC
Typical response time
< 0.7 s
Net weight
3.3 kg
Insulation voltage input / PE
3.5 kV AC (type test)
Assembly instructions
alignable: PN ≥50%, 5 mm horizontally, 15 mm next to active components, 50 mm verticallyalignable: PN <50%, 0 mm horizontally, 40 mm vertically top, 20 mm vertically bottom
Conductor cross section flexible min.
0.2 mm²
Standard – Electronic equipment for use in electrical power installations and their assembly into electrical power installations
EN 50178/VDE 0160 (PELV)
Rail applications
EN 50121-4
Electrostatic discharge
EN 61000-4-2
Test field strength
10 V/m (Test Level 3)
Wireless telephone simulation
ENV 50204
China RoHS
Environmentally Friendly Use Period = 25;
ECLASS 5.1
27049000
ETIM 4.0
EC000599
UNSPSC 12.01
39121004
UNSPSC 18.0
39121004
Installation distance right/left
5 mm / 5 mm
Degree of protection
IP20
Installation height
4000 m
AC frequency range
45 Hz ... 65 Hz
Nominal power consumption
1157 VA
Inrush current
< 15 A (typical)
Protective circuit/component
Varistor, gas-filled surge arrester
Derating
60 °C ... 70 °C (2.5%/K)
Connection in series
yes
Efficiency
> 92 % (for 230 V AC and nominal values)
Mounting position
horizontal DIN rail NS 35, EN 60715
Conductor cross section AWG min.
24
EMC requirements for noise immunity
EN 61000-6-1
Standard - Electrical safety
IEC 60950-1/VDE 0805 (SELV)
Standard - Safe isolation
DIN VDE 0100-410
Standard - Equipment safety
BG (design tested)
Low Voltage Directive
Conformance with Low Voltage Directive 2014/35/EC
Frequency range
0.15 MHz ... 80 MHz
Comments
Criterion A
Signal
1 kV (Test Level 2 - asymmetrical)
Conducted interference
EN 61000-4-6
Frequency
900 MHz
Field intensity
20 V/m
ECLASS 4.1
27040700
ECLASS 5.0
27049000
ECLASS 6.0
27049000
ECLASS 7.0
27049002
UNSPSC 6.01
30211502
UNSPSC 21.0
39121004
Current consumption
8.8 A (120 V AC)
Power factor (cos phi)
0.88
POWER BOOST (IBoost)
45 A (-25 °C ... 40 °C permanent, UOUT = 24 V DC )
Residual ripple
< 30 mVPP (with nominal values)
Power loss nominal load max.
80 W
Insulation voltage input/output
4 kV AC (type test)
Connection method
Screw connection
Conductor cross section flexible max.
4 mm²
Conductor cross section AWG max.
10
EMC requirements for noise emission
EN 61000-6-3
Standard – Protection against shock currents, basic requirements for protective separation in electrical equipment
EN 50178
UL approvals
UL Listed UL 508
Shipbuilding approval
DNV GL (EMC A), ABS, LR, RINA, NK, BV
Electromagnetic HF field
EN 61000-4-3
Input
2 kV (Test Level 3 - symmetrical)
Voltage
10 V (Test Level 3)
Criterion A
Normal operating behavior within the specified limits.
ECLASS 11.0
27040701
ECLASS 4.0
27040700
ETIM 2.0
EC001039
UNSPSC 7.0901
39121004
UNSPSC 19.0
39121004
CSA
CSA-C22.2 No. 107.1-01
Discharge in air
15 kV (Test Level 4)
Fast transients (burst)
EN 61000-4-4
Surge voltage load (surge)
EN 61000-4-5
I/O/S
asymmetrical
REACh SVHC
Lead 7439-92-1
ECLASS 9.0
27040701
ETIM 7.0
EC002540
UNSPSC 11
39121004
UNSPSC 20.0
39121004
Contact discharge
8 kV (Test Level 4)
Output
1 kV (Test Level 2 - symmetrical)
Criterion B
Temporary impairment to operational behavior that is corrected by the device itself.
ECLASS 10.0.1
27040701
ETIM 3.0
EC001039
ETIM 6.0
EC002540
UNSPSC 13.2
39121004

Product condition