2700577 Phoenix Contact Electrical Safety Devices

2700577 Product Details

• Height
  112.2 mm
• Rated control circuit supply voltage US
  24 V DC -15 % / +10 % (A1/A2)
• Input current at UD
  6 mA (at 31-A2 for UD; depending on load + 100 mA at M1 and 32)
• Switching voltage
  min. 20.4 V DC
• Sq. Total current
  36 A2 (13/14, see to derating)
• Designation
  Air clearances and creepage distances between the power circuits
• Maximum inrush current
  500 mA (Δt = 1 ms at Us)
• Short-circuit protection
  no
• Mounting position
  vertical, horizontal, with front of module upward
• pluggable
  Yes
• Screw thread
  M3
• Rated insulation voltage
  250 V AC
• Vibration (operation)
  10 Hz ... 150 Hz, 2g
• GL
  C, EMC2
• ECLASS 10.0.1
  27371819
• ECLASS 4.1
  40020600
• ETIM 7.0
  EC001449
• Ambient temperature (storage/transport)
  -40 °C ... 85 °C
• Power consumption at US
  typ. 1.2 W
• Diagnostic supply voltage UD
  24 V DC -15 % / +10 % (31/A2, TBUS)
Contact type
1 confirmation current path
Output fuse
150 mA fast blow
Typical pickup time at US
< 100 ms (with Us when controlled via A1)
Relay type
Electromechanical relay with force-guided contacts in accordance with IEC/EN 61810-3
Min. degree of protection of inst. location
IP54
Status display
1 x green LED
Conductor cross-section AWG
24 ... 12
Conductor cross section flexible
0.2 mm² ... 2.5 mm²
Rated surge voltage/insulation
Safe isolation, 6 kV reinforced insulation from control circuit, start circuit, confirmation current path, signal output to the enabling current path; 4 kV/basic insulation between all current paths and housing
Degree of pollution
2
Environmental simulation test
ISA-S71.04 (G3)
Ambient temperature (operation)
-40 °C ... 70 °C (observe derating)
Input voltage range "0" signal
0 V DC ... 5 V DC (for safe Off)
Inrush current
min. 1 mA
Inrush current at UD
typ. 2.5 A (Δt < 20 µs at UD)
Number of outputs
1 (non-safety-related)
Switching capacity
min. 20 mW
Switching capacity according to IEC 60947-5-1
4 A (24 V (DC13); N/O contact 13/14)
Typical release time at US
< 35 ms (when controlled via A1)
Nominal operating mode
100% operating factor
Mounting type
DIN rail mounting
Housing material
PBT
Operating voltage display
1 x yellow LED
Conductor cross section solid
0.2 mm² ... 2.5 mm²
Torque
0.5 Nm ... 0.6 Nm
Safety Integrity Level (SIL)
3
Utilization restriction
EMC: class A product, see manufacturer's declaration in the download area
Depth
114.5 mm
Maximum altitude
≤ 2000 m (Above sea level)
Rated control supply current IS
typ. 50 mA
Filter time
max. 2 ms (at A1-A2; test pulse width)
Output description
PNP
Contact material
AgCuNi, + Au
Switching frequency
max. 0.5 Hz
Current
max. 100 mA
Recovery time
500 ms
Assembly instructions
See derating curve
Housing color
yellow
Connection method
Screw connection
Stripping length
7 mm
Standards/regulations
DIN EN 50178, EN 60079-15
Overvoltage category
III
IECEx
Ex nA nC IIC T4 Gc
China RoHS
Environmentally Friendly Use Period = 50 years
ECLASS 7.0
27371819
Width
12.5 mm
Max. permissible relative humidity (operation)
75 % (on average, 85% infrequently, non-condensing)
Max. permissible humidity (storage/transport)
75 % (on average, 85% infrequently, non-condensing)
Input current range "0" signal
0 mA ... 2 mA (for safe Off)
Protective circuit
Serial protection against polarity reversal 33 V suppressor diode (A1/A2)33 V suppressor diode (31/A2)
Output name
Confirmation current path
Limiting continuous current
100 mA
Mechanical service life
10x 106 cycles
Voltage
approx. 22 V DC (UD - 2 V)
Net weight
189.1 g
Degree of protection
IP20
Indication
1 x red LED
Stop category
0
Shock
15g
Conformance
CE-compliant
REACh SVHC
Lead 7439-92-1
ECLASS 4.0
40020600
ECLASS 6.0
27371800
ATEX
 II 3 G Ex nA nC IIC T4 Gc
UL, USA/Canada
cULus
ECLASS 5.0
27371900
ECLASS 9.0
27371819
ECLASS 11.0
27371819
ECLASS 5.1
27371900
ETIM 6.0
EC001449

Product condition