1210902 Phoenix Contact Electrical Wires & Cables

Product Details

• Application
  For charging with alternating current (AC) and with direct current (DC)
• Note on the connection method
  Crimp connection, cannot be disconnected
• Width
  108 mm
• Type of charging current
  DC, AC 1-phase
• Rated voltage for signal contacts
  30 V AC
• Temperature measurement
  DC contacts: 2x PT1000 (DIN EN 60751)
• Charging mode
  Mode 2, 3, 4
• Height
  151.2 mm
• Max. altitude
  4000 m (above sea level)
• Rated current of power contacts
  48 A AC
• Insertion/withdrawal cycles
  > 10000
• Restrictions to mounting position
  Only 0 to 90 degree frontal inclination possible, see figure
• Screws included in the scope of delivery
  none
• Material surface of contacts
  Ag
• External cable diameter
  1.6 mm -0.2 mm
• Number of positions of theconnectors
  4
• Pause time after entry or exit path
  3 s
• Service life insertion cycles
  > 10000 load cycles
• Cable length
  1 m
• ECLASS 11.0
  27144706
Standards/regulations
DIN EN 60751
Depth
122.8 mm
Ambient temperature (operation)
-40 °C ... 80 °C
Degree of protection
IP55 (plugged in; when plugged in and ready to operate, the degree of protection is only ensued if both plug-in components are original products from Phoenix Contact or suitable standard-compliant products)
Number of power contacts
5 (L1, N, PE, DC+, DC-)
Rated current for signal contacts
2 A
Withdrawal force
< 100 N
Design line
Generation 4
Customer variations
On request
Flammability rating
V0
Cable weight
7 kg/km
External sheath, color
Green-yellow
Maximum voltage for locking detection
12 V
Recommended measured current
≤ 1 mA (Umax= 16 V DC)
Type of sensor
Pt 1000
ECLASS 10.0.1
27144706
Charging standard
CCS type 1
Bore dimensions
117.6 mm x 90 mm, 117.6 mm x 83 mm
Ambient temperature (storage/transport)
-40 °C ... 85 °C
Number of phases
1
Number of signal contacts
2 (CP, CS)
Resistor coding
2.7 kΩ (between PE and CS)
Temperature monitoring
AC contacts: PTC chain (DIN˽EN˽60738-1)
Required mounting screws
M6
Locking type
Locking in the inserted state with a locking mechanism
Cable resistance
≤ 37.1 Ω/km
Possible power supply range at the motor
9 V ... 16 V
Recommended adaptation time
600 ms
Mechanical emergency release
available
Resistance range
650 Ω ... 1450 Ω
Type
Locking actuator top
Design
Generation 4
Note
A protective cap is supplied as standard for the DC and AC contacts.
Conductor length
2 m (AC cables)
Maximum charging power
250 kW
Rated voltage for power contacts
250 V AC
Insulation resistance of neighboring contacts
> 200 MΩ
Type of signal transmission
Pulse width modulation with modulated Powerline communication according to ISO/IEC 15118 / DIN SPEC 70121
Insertion force
< 100 N
Material
Plastic
Cable structure
4 x 0.5 mm²
Single wire, color
black PP/CS
Operating voltage
12 V (Typical power supply at the motor)
Typical motor current for locking
0.25 A
Reverse current of the motor
max. 1.5 A
Tolerance at the sensor with the recommended measured current
±5K
Mounting hole diameter
6.80 mm (ø)
Mounting position of the locking actuator
Top center
Housing color
black
Outer sheath, material
PVC
Minimum bending radius
15 mm
Max. dwell time with reverse current
1 s
Lock recognition
available
Temperature range
-40 °C ... 130 °C
ECLASS 9.0
27144706