OMT600-R200-IEP-IO-0,3M-V31-L Pepperl + Fuchs Electronic Components

Product Details

• Cable length
  0.3 m
• Mass
  approx. 41 g
• Optical face
  PMMA
• Housing
  PC (Polycarbonate)
• Connection
  fixed cable 300 mm with M8 x 1 male connector; 4-pin
• Degree of protection
  IP67 / IP69 / IP69K
• Housing depth
  41.7 mm
• Storage temperature
  -40 ... 70 °C (-40 ... 158 °F)
• Housing height
  50.6 mm
• Housing width
  15 mm
• Ambient temperature
  10 ... 50 °C (50 ... 122 °F)
• CCC approval
  CCC approval / marking not required for products rated ≤36 V
• FDA approval
  IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007
• UL approval
  E87056 , cULus Listed , class 2 power supply , type rating 1
• EAC conformity
  TR CU 020/2011
• Warm up time
  5 min
• Repeat accuracy
  < 1 %
• Linearity error
  0.75 %
• Temperature drift
  0.05 %/K
• Laser safety
  EN 60825-1:2014
Recovery time
2 ms
Load resistor
> 1 kΩ voltage output ; ≤ 470 Ω current output
Product standard
EN 60947-5-2
Communication interface
IEC 61131-9
Response time
2 ms
Usage category
DC-12 and DC-13
Output type
1 current output: 4 ... 20 mA
Compatible master port type
A
Switching voltage
max. 30 V DC
Voltage drop
≤ 1.5 V DC
Signal output
1 push-pull output , 1 analog output , short-circuit-proof, reverse polarity protection, surge-proof
Switching current
max. 100 mA , resistive load
Switching type
The default setting is: C/Q - Pin4: NPN normally open, PNP normally closed, IO-Link, I—Pin2: analog output 4...20 mA
Min. cycle time
3 ms
Process data width
Process data input 4 byte, Process data output 2 bits
SIO mode support
yes
Transfer rate
COM2 (38.4 kBit/s)
IO-Link revision
1.1
Device profile
Identification and diagnosis, Smart Sensor type 0/type 3.3
Interface type
IO-Link ( via C/Q = pin 4 )
Device ID
0x111908 (1120520)
No-load supply current
< 18 mA at 24 V supply voltage
Protection class
III
Operating voltage
18 ... 30 V DC
Control elements
Teach-In key
Ripple
max. 10 %
Operation indicator
LED green: constantly on - power on, flashing (4Hz) - short circuit, flashing with short break (1 Hz) - IO-Link mode
Diagnostic Coverage (DC)
0 %
Function indicator
LED yellow: constantly on - switch output active, constantly off - switch output inactive
MTTFd
470 a
Mission Time (TM)
20 a
Resolution
0.1 mm
Opening angle
approx. 0.3 °
Angle deviation
max. +/- 1.5 °
Ambient light limit
EN 60947-5-2 : 15000 Lux
Diameter of the light spot
approx. 3 mm at a distance of 600 mm
max. pulse energy
< 40 nJ
Repetition rate
approx. 2.4 kHz
Wave length
680 nm
Laser class
1
Note
LASER LIGHT , DO NOT STARE INTO BEAM
Light source
laser diode
Light type
modulated visible red light
Pulse length
5.5 µs
Reference target
standard white, 100 mm x 100 mm
Measurement range
100 ... 600 mm
Beam divergence
> 5 mrad, d63 < 2,8 mm in the range of 350 mm ... 800 mm

Related documents OMT600-R200-IEP-IO-0,3M-V31-L Specs