X20CP1382 B&R Electronic Components

Product Details

• Weight310 g
• Temperature Operation Vertical mounting orientation
  -25 to 50°C
• Max. error Voltage Offset
  0.04% (Rev.
• Temperature Operation Horizontal mounting orientation
  -25 to 60°C
• Max. error Current Offset
  0 to 20 mA = 0.1% (Rev.
• Permissible input signal Current
  Max. ±50 mA
• Max. gain drift Current
  0 to 20 mA = 0.015 %/°C / 4 to 20 mA = 0.023 %/°C
• Max. gain drift Voltage
  0.017 %/°C
• Permissible input signal Voltage
  Max. ±30 V
• Load Current
  <300 Ω
• Load Voltage
  -
• Input impedance in signal range Voltage
  20 MΩ
• Input impedance in signal range Current
  -
• Output format Current
  INT 0x0000 - 0x7FFF / 1 LSB = 0x0008 = 4.883 μA
• Output format Voltage
  INT 0x8001 - 0x7FFF / 1 LSB = 0x0008 = 2.441 mV
• Digital converter resolution Voltage
  ±12-bit
• Output format Data type
  INT
• Digital converter resolution Current
  12-bit
• Switching threshold High
  >15 VDC
• Switching threshold Low
  <5 VDC
Input filter Software
Default 1 ms, configurable between 0 and 25 ms in 0.1 ms increments
Input filter Hardware
Standard inputs and mixed channels: ≤200 μs; High-speed inputs: ≤2 μs, when used as standard inputs: ≤200 μs
Interface IF7 Controller
SJA 1000
Interface IF7 Terminating resistor
Integrated in module
Interface IF7 Transfer rate
Max. 1 Mbit/s
Interface IF7 Max. distance
1000 m
Interface IF7 Variant
Connection via 16-pin terminal block X20TB1F
Interface IF7 Signal
CAN bus
Interface IF6 Fieldbus
X2X Link master
Interface IF5 Max. output current
0.1 A
Interface IF5 Variant
Type A
Interface IF5 Type
USB 1.1/2.0
Interface IF4 Max. output current
0.5 A
Interface IF4 Variant
Type A
Interface IF4 Type
USB 1.1/2.0
Interface IF3 Transfer rate
100 Mbit/s
Interface IF3 Variant
1x RJ45 shielded
Interface IF3 Line length
Max. 100 m between 2 stations (segment length)
Interface IF3 Type
Type 4
Interface IF3 Fieldbus
POWERLINK managing or controlled node
Interface IF2 Transfer rate
10/100 Mbit/s
Interface IF2 Line length
Max. 100 m between 2 stations (segment length)
Interface IF2 Variant
1x RJ45 shielded
Interface IF2 Signal
Ethernet
Interface IF1 Transfer rate
Max. 115.2 kbit/s
Interface IF1 Signal
RS232
Interface IF1 Max. distance
900 m
Interface IF1 Variant
Connection via 16-pin terminal block X20TB1F
Processor L2 cache
128 kB
Application memory Error-correcting code (ECC)
Yes
Application memory Data retention
10 years
Application memory Guaranteed erase/write cycles
20,000
Application memory Type
2 GB eMMC flash memory
Standard memory RAM
256 MB DDR3 SDRAM
Processor Clock frequency
400 MHz
Processor Type
Vx86EX
Certifications EAC
Yes
Certifications ABS
Yes
Certifications KR
Yes
Certifications LR
ENV1
Certifications UL
cULus E115267; Industrial control equipment
Certifications DNV
Temperature: B (0 - 55°C); Humidity: B (up to 100%); Vibration: B (4 g); EMC: B (bridge and open deck)
Certifications ATEX
Zone 2, II 3G Ex nA nC IIA T5 Gc; IP20, Ta (see X20 user's manual); FTZÚ 09 ATEX 0083X
Certifications HazLoc
cCSAus 244665; Process control equipment; for hazardous locations; Class I, Division 2, Groups ABCD, T5
Certifications UKCA
Yes
Power consumption Internal I/O
2.3 W
Support reACTION-capable I/O channels
No
Certifications CE
Yes
Support Visual Components support
Yes
Support ACOPOS support
Yes
Support Controller redundancy
No
Diagnostics Terminating resistor
Yes, using LED status indicator
Diagnostics Temperature
Yes, using software register
Diagnostics Inputs
Analog inputs: Yes, using LED status indicator and software
Diagnostics I/O power supply
Yes, using LED status indicator
Diagnostics POWERLINK
Yes, using LED status indicator
Diagnostics Supply voltage monitoring
Yes, using LED status indicator
Diagnostics Ethernet
Yes, using LED status indicator
Diagnostics RS232 data transfer
Yes, using LED status indicator
Diagnostics CAN bus data transfer
Yes, using LED status indicator
Diagnostics CPU function
Yes, using LED status indicator
Diagnostics Outputs
Digital outputs: Yes, using LED status indicator and software (output error status)
Note
X20 end cover plate (right) included in delivery; 3 X20 terminal blocks (16-pin) included in delivery; Interface module slot cover included in delivery
Degree of protection per EN 60529
IP20
Electrical isolation
Ethernet (IF2), POWERLINK (IF3) and X2X (IF6) isolated from each other, from other interfaces and from PLC; Channel isolated from bus; Channel not isolated from channel or PLC
Braking voltage when switching off inductive loads
Standard outputs and mixed channels: Typ. 45 VDC
Switch-on in the event of overload shutdown or short-circuit shutdown
Standard outputs and mixed channels: Approx. 10 ms (depends on module temperature); High-speed outputs: No switch-on
Peak short-circuit current
Standard outputs and mixed channels: <3 A; High-speed outputs: <20 A
RDS(on)
140 mΩ
Residual voltage
Standard outputs and mixed channels: <0.1 V at nominal current 0.5 A; High-speed outputs: <0.9 V at nominal current 0.1 A
Leakage current when the output is switched off
Standard outputs and mixed channels: 5 µA; High-speed outputs: 25 µA
Diagnostic status
Standard outputs and mixed channels: Output monitoring with 10 ms delay; High-speed outputs: Output monitoring with 10 µs delay
Output circuit
Standard outputs and mixed channels: Source; High-speed outputs: Sink or source
Switching voltage
24 VDC -15% / +20%
Output protection
Thermal shutdown in the event of overcurrent or short circuit (see value "Short-circuit peak current"); Internal freewheeling diode for switching inductive loads (see section "Switching inductive loads")
Total nominal current
Standard outputs and mixed channels: 4 A; High-speed outputs: 0.8 A
Nominal output current
Standard outputs and mixed channels: 0.5 A; High-speed outputs: 0.2 A
Standardized range of values for resistance measurement
0.1 to 4000.0 Ω
Variant
Standard outputs and mixed channels: Current-sourcing FET; High-speed outputs: Push-Pull
Nonlinearity
<0.05%
Max. offset drift
0.012%/°C
Measurement current
1 mA
Resistance measurement resolution
1 LSB = 0x0005 = 0.49 Ω
Max. gain drift
0.023 %/°C
Linearization method
Internal
Permissible input signal
Short-term max. ±30 V
Sensor standard
EN 60751
Temperature sensor resolution
1 LSB = 0x0005 = 0.16°C
Output format
INT or UINT for resistance measurement
Resistance measurement range
0.1 to 4000 Ω
Crosstalk between channels
<-70 dB
Digital converter resolution
13-bit
Input voltage
24 VDC -15% / +20%
Common-mode range
±12 V
Output of digital value during overload
Configurable
Conversion procedure
SAR
Input filter
Third-order low-pass filter / Cutoff frequency 1 kHz
Input protection
Protection against wiring with supply voltage
Type of signal lines
Shielded lines must be used for all high-speed digital inputs/outputs, line length: Max. 20 m
Conversion time
1 channel enabled: 100 µs; 2 channels enabled: 200 µs
Max. error Current Gain
0 to 20 mA = 0.15% (Rev.
Max. error Voltage Gain
0.18% (Rev.
Interface IF3 Transfer Auto-MDI/MDIX
Yes
Interface IF3 Transfer Autonegotiation
Yes
Interface IF3 Transfer Full-duplex
POWERLINK mode: No / Ethernet mode: Yes
Interface IF3 Transfer Half-duplex
Yes
Interface IF2 Transfer Auto-MDI/MDIX
Yes
Interface IF2 Transfer Full-duplex
Yes
Interface IF2 Transfer Autonegotiation
Yes
Interface IF3 Transfer Physical layer
100BASE-TX
Interface IF2 Transfer Half-duplex
Yes
Interface IF2 Transfer Physical layer
10BASE-T/100BASE-TX
Application memory Writable data amount Results for 5 years
21.9 GB/day
Application memory Writable data amount Guaranteed
40 TB
Processor L1 cache Program code
16 kB
Processor L1 cache Data code
16 kB
Relative humidity Operation
5 to 95%, non-condensing
Dimensions Height
99 mm
Relative humidity Transport
5 to 95%, non-condensing
Dimensions Depth
75 mm
Dimensions Width
164 mm
Temperature Storage
-40 to 85°C
Temperature Transport
-40 to 85°C
Relative humidity Storage
5 to 95%, non-condensing
Temperature Derating
See section "Switching frequency derating for high-speed digital outputs".
Mounting orientation Vertical
Yes
Mounting orientation Horizontal
Yes
Installation elevation above sea level 0 to 2000 m
No limitation
Installation elevation above sea level >2000 m
Reduction of ambient temperature by 0.5°C per 100 m
Switching frequency Inductive load
See section "Switching inductive loads".
Switching frequency Resistive load
Standard outputs and mixed channels: Max. 500 Hz; High-speed outputs: 50 kHz, max. 200 kHz (see section "Switching frequency derating for high-speed digital outputs")
Switching delay 1 → 0
Standard outputs and mixed channels: <300 µs; High-speed outputs: <3 µs
Pulse width modulation Period duration
5 to 65535 µs corresponds to 200 kHz to 15 Hz
Pulse width modulation Pulse duration
0 to 100%, minimum 2.5 µs
Switching delay 0 → 1
Standard outputs and mixed channels: <300 µs; High-speed outputs: <3 µs
Pulse width modulation Resolution for pulse duration
0.1% of the configured frequency
Temperature sensor normalization Pt1000
-200 to 850°C
Sensor Pt1000
-200 to 850°C
Max. error at 25°C Offset
0.15% (Rev.
Nonlinearity Voltage
<0.025%
Nonlinearity Current
<0.05%
Max. error at 25°C Gain
0.3% (Rev.
Max. offset drift Current
0 to 20 mA = 0.008 %/°C / 4 to 20 mA = 0.012 %/°C
Common-mode rejection 50 Hz
70 dB
Common-mode rejection DC
70 dB
Max. offset drift Voltage
0.008 %/°C
Input
±10 V or 0 to 20 mA / 4 to 20 mA, via different terminal connections
Input type
Differential input
Power consumption for X2X Link power supply
0.8 W
Measurements per module
Each function up to 2x
Status indicators
CPU function, Ethernet, POWERLINK, RS232, CAN bus, CAN bus terminating resistor, PLC power supply, I/O power supply, I/O function per channel
Counter frequency
250 kHz
Timestamp
1 µs resolution
Possible measurements
Period measurement, gate measurement, differential time measurement, edge counter, edge times
Signal form
Square wave pulse
Encoder inputs
24 V, asymmetrical
Input frequency
Max. 100 kHz
Counter size
32-bit
Encoder power supply
Module-internal, max. 300 mA
Power consumption without interface module and USB
5.5 W
Evaluation
4x
Overload characteristics of encoder power supply
Short-circuit proof, overload-proof
Additional functions
X2 - High-speed digital inputs:; 2x 250 kHz event counting, 2x AB counter, ABR incremental encoder, direction/frequency, period measurement, gate measurement, differential time measurement, edge counters, edge times
Input resistance
X1 - Standard inputs: 6.8 kΩ; X2 - Standard inputs: 8.9 kΩ; X2 - High-speed inputs: 6.8 kΩ; X3 - Mixed channels: 8.9 kΩ
Input circuit
Sink
Connection type
1-wire connections
Input current at 24 VDC
X1 - Standard inputs: Typ. 3.5 mA; X2 - Standard inputs: Typ. 2.68 mA; X2 - High-speed inputs: Typ. 3.5 mA; X3 - Mixed channels: Typ. 2.68 mA
Nominal voltage
24 VDC
Shortest task class cycle time
1 ms
Typical instruction cycle time
0.0199 µs
Quantity
14 standard inputs, 4 high-speed inputs and 4 mixed channels, configuration as input or output using software
Remanent variables
32 kB FRAM, retention >10 years
Modular interface slots
1
Integrated I/O processor
Processes I/O data points in the background
FPU
Yes
Real-time clock
Retention for at least 300 hours, typ. 1000 hours at 25°C, 1 s resolution, -18 to 28 ppm accuracy at 25°C
Permissible contact load
10 A
Nominal output voltage
24 VDC
Parallel connection
Yes
Redundant operation
Yes
System module
Controller
Fuse
Integrated, cannot be replaced
Nominal output power
2 W
Input current
Max. 1 A
Reverse polarity protection
Yes
B&R ID code
0xDABB
Interfaces
1x RS232, 1x Ethernet, 1x POWERLINK, 2x USB, 1x X2X Link, 1x CAN bus
Cooling
Fanless

Related documents X20CP1382 Specs